Fujitsu F2MC-16LX Series Hardware Manual Download | Manualshive

Page: 400 / 710

background image

382

CHAPTER 14 UART0

14.1

Overview of UART0

The UART0 is a general-purpose serial-data communication interface for synchronous
or asynchronous communication with external devices.
• Incorporates a bidirectional communication function (clock synchronous and

asynchronous modes)

• The master/slave communication function (multiprocessor mode) is incorporated.
• Capable of generating an interrupt request upon transmission, reception, or detection

of a reception error.

• Supports expansion intelligent I/O service (EI

2

OS)

■

Functions of UART0

●

Functions of UART0

The UART0 is a general-purpose serial data communication interface to exchange serial data with external

devices. Its functions are listed in Table 14.1-1.

Table 14.1-1 Function of UART0

Function

Data buffer

Full-duplicate double-buffer

Transfer mode

• Synchronous to clock (without start bit/stop bit and parity

bit)

• Asynchronous (start-stop synchronization to clock)

Baud rate

• Special-purpose baud-rate generator, selectable 10 types
• Any baud rate can be set by external clock.
• A clock supplied from the internal clock (16-bit reload timer

0) can be used.

Data length

• 7 bits (for asynchronous normal mode only)
• 8 bits

Signal type

NRZ (Non Return to Zero) type

Detection of receive error

• Framing error
• Overrun error
• Parity error (Not supported in operation mode 1)

interrupt request

• Detection of receive error
• Transmission interrupt (Transmission)

• Both the transmission and reception support EI

2

OS.

Master/slave type communication

function (multi processor mode)

This function enables communications between 1 (only use
master) and n (slave) (This function is used only as the master
side)

Note:

At clock synchronous transfer, data is transferred alone with neither start nor stop bit added.

«
...
398
399
400
401
402
...
»

Summary of Contents for F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2MC-16LX Series

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Brand: ADS Technologies Pages: 1

Brand: Bailey Pages: 33

LITTLE BOARD P5X

Brand: Ampro Corporation Pages: 121

Brand: Planet Pages: 20

Brand: WTI Pages: 178

Internal All-in-One Digital Media Drive ULT31793

Brand: Ultra Products Pages: 1

Brand: EVGA Pages: 3

Brand: R.V.R. Elettronica Pages: 171

RJModem MT5656RJ

Brand: Multi-Tech Pages: 27

Brand: Adaptec Pages: 2

Brand: Renesas Pages: 6

Brand: Altronix Pages: 8

SCREENSHARE PRO

Brand: V7 Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands