OPERATING INSTRUCTIONS
AGT 1060
Rev.09/2020
20
•
Always make sure that all the protections are in place and that they cover all the rotating
parts, including the “crosses” on both sides of the universal joint.
•
Do not use the universal joints if the safety guards are not installed.
•
Avoid angles exceeding 15° to ensure a long service life of the universal joint.
•
Before engaging rotation, secure the protections with a chain and make sure that the
safety guards of the universal joint on the tractor and on the implement are coupled
(attached).
2.8.4
IMPROPER USE OF IMPLEMENTS
•
Do not allow any unauthorized persons to stand between the tractor and the implement
when the latter is in operation or when the implement is attached or detached from the
tractor.
•
Attach the universal joint following the order Implement
→
Tractor.
Never attach it in
reverse order, otherwise this could result in serious injuries or even death.
•
Rotating shafts without protections are very dangerous.
•
Do not touch rotating universal joints! Keep at a safety distance of 1.5 m from the
rotating universal joint.
•
Do not engage the PTO drive shaft on the tractor for no reason and make sure that the
angular difference at the couplings of the universal joint is not too large.
•
Do not connect the electrical and hydraulic system to implements (mounted or trailed)
when the tractor is running; only connect these systems, when tractor is safely stopped.
•
Do not use any implements when the universal joint is not connected properly.
•
Do not attach any implements which do not meet all conditions for safe use or without
appropriate signalling devices, without appropriate safety devices or when the tractor
capacity is not compatible with the implement.
•
Do not attach any trailed implements to the front tow bar of the tractor; this tow bar is
only designed to tow a tractor in case of a break-down (without implements installed).
•
Make sure the tractor is not overloaded by the implement and when the tractor is under
heavy load, ensure proper stability by adding suitable weights.
2.9
SAFETY INSTRUCTIONS FOR OPERATING THE TRACTOR ON ROADS
Do not drive on public roads. If this cannot be avoided, you must comply with the following
instructions.
•
When driving the tractor, follow the road traffic rules.
•
Always make sure that the brake pedals are coupled together before driving.
•
If you intend to drive the tractor on public roads, make sure it is equipped with signal
lights and signs, in accordance with road traffic rules.
•
Make sure that the signal lights on the tractor and the implement (if used) are in perfect
working order.
•
Check the condition of tyres (pressure and wear).
•
The lift mechanism must be securely fixed in the upper position when driving.
•
If you are driving a tractor with an implement attached, reduce speed and take into
account that the braking distance (depending on the weight) is significantly increased.
•
When driving the tractor on the road, the seat should always be turned to the normal
driving position (see the chapter TERMS), never in the opposite direction.
•
Always use the foot throttle when driving on the road. The manual throttle must be
adjusted to minimum.
•
When driving, always adapt to traffic and road conditions, pay attention to underpasses or
public utility lines to avoid contact with the highest point of the tractor.
Summary of Contents for AGT 106
