MA Lighting Technology GmbH . Dachdeckerstr. 16 . D-97297 Waldbüttelbrunn . www.malighting.de eMail: [email protected]
38
38
38
38
38
2.9.4 ARTNET DMX-ETHERNET-CONFIGURATION
2.9.4 ARTNET DMX-ETHERNET-CONFIGURATION
2.9.4 ARTNET DMX-ETHERNET-CONFIGURATION
2.9.4 ARTNET DMX-ETHERNET-CONFIGURATION
2.9.4 ARTNET DMX-ETHERNET-CONFIGURATION
You can call up this menu by pressing a button in the CONFIGURATION column, if the PathPort protocol has been
selected
It is possible to connect up to 16 Ethernet DMX Converter. On the DMX converters, unique SUB NET addresses
have to be designated accordingly. The address switches of the individual DMX sockets have to be set to four dif-
ferent addresses. The settings modified on the DMX converter, can be overwritten by software.
Artnet - Note
Configuration, next page
If Artnet converters are connected, they will be searched for and displayed in the chart when calling up this
menu. If the converter is being activated after opening the menu, you can search for the converter by pressing
DMX IN can be used to merge the signals of a second console with those of the grandMAs (MERGE) and pipe them
to the stage on the same line. If channels from the grandMA and of the second console are triggered in this
connection, the higher value will be sent (HTP).
The DMX-In can be used as an additional remote control channel
8.3
8.3
8.3
8.3
8.3
Remote control by DMX IN
Attention:
Attention:
Attention:
Attention:
Attention:
If you are in a network connection of Master-Slave, only the DMX IN of the Master console will be
transferred to the internal DMX port. The DMX IN of the Slave console can only be used for remote control
purposes.
2.
2.
2.
2.
2.99999.2
.2
.2
.2
.2 Configuring the internal DMX ports 1(A) - 8(H)
Configuring the internal DMX ports 1(A) - 8(H)
Configuring the internal DMX ports 1(A) - 8(H)
Configuring the internal DMX ports 1(A) - 8(H)
Configuring the internal DMX ports 1(A) - 8(H)
By pressing a button in the PROTOCOL column, you can set a protocol for the appropriate DMX port (A-H) (referred
to the respective Ethernet DMX converter) for the transmissions.
By pressing a button in the CONFIGURATION column, you can call up the appropriate menu for this DMX output.
next pages
If the button is on “
enabled if Idle
enabled if Idle
enabled if Idle
enabled if Idle
enabled if Idle
or Playback
or Playback
or Playback
or Playback
or Playback
“, a DMX output via Ethernet is on, if the unit is not in a
session (Idle). An exception is here the Playback Session, in this case the Slave stays on.
In a Master-Slave configuration (Full-Tracking and Multi-User Session), the Slaves switch itselv to
„Disable“ (off). If a Master fails, the Slave with the higher priority will automatically be switched to
„Enable“. This way, the DMX will now be created by the former Slave (now Master). If two units are
switched to „Enable“, the data may will overlap. This has to be avoided under all cicrumstances!
By pressing on this button, it will switch to “disabled“; now, a DMX output via Ethernet is no longer possible.
next pages
2.9.3 DMX-CONFIGURATION at Micro
2.9.3 DMX-CONFIGURATION at Micro
2.9.3 DMX-CONFIGURATION at Micro
2.9.3 DMX-CONFIGURATION at Micro
2.9.3 DMX-CONFIGURATION at Micro
Open this menu with TOOLS. It is a compressed versionof the TOOLS-menus of the „big“ grandMAs.
With the menu „Ethernet Configuration Setup“ you can change the IP-address and the name of the desk. With
START SESSION the Micro connects with grandMA 3D .
The Micro can not be connected to NSPs and other
grandMAs
.
