manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

RapidIO Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

16-183

QFI

4

0

Queue Full Interrupt
If the queue is full and the IMxMR[QFIE] bit is set, QFI is set and an interrupt is generated. QFI s 
cleared by writing a 1 to it.

—

3

0

Reserved. Write to zero for future compatibility. 

MB

2

0

Mailbox Busy
Indicates that a message operation is in progress. MB is cleared when an error occurs or the 
message operation finishes. Read only.

QE

1

1

Queue Empty
If the queue is empty, this bit is set. QE is also set if the message controller is disabled. Read 
only.

MIQI

0

0

Message-In-Queue Interrupt
If the queue has accumulated the number of messages specified by the IMxMR[MIQ_THRESH] 
and the IMxMR[MIQIE] bit is set, this bit is set and an interrupt is generated. This bit is cleared 
by writing a 1 to it.

Table 16-115.  IMxSR Field Descriptions (Continued)

Bits

Reset Description

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Ubiquiti M900 Quick Start Manual preview
M900
Brand: Ubiquiti Pages: 24
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
Black Box LT2060A Manual preview
LT2060A
Brand: Black Box Pages: 37
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
ekwb EK-FC285 GTX Classified Installation And Mounting Manual preview
EK-FC285 GTX Classified
Brand: ekwb Pages: 2
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
SilverStone ECU06 Installation Manual preview
ECU06
Brand: SilverStone Pages: 17
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
MikroTik Network Controller Manual preview
Network Controller
Brand: MikroTik Pages: 6
ELC dmXLAN node6x User Manual preview
dmXLAN node6x
Brand: ELC Pages: 12
Acer AN1600 F1 Specifications preview
AN1600 F1
Brand: Acer Pages: 22
Acer Altos S200F User Manual preview
Altos S200F
Brand: Acer Pages: 58
StarTech.com 8STUSBDUP12 Instruction Manual preview
8STUSBDUP12
Brand: StarTech.com Pages: 20

Brands by name

Popular brands

Load more brands