Freescale Semiconductor MSC8144E Reference Manual Download

Page: 310 / 1374

MSC8144E Reference Manual, Rev. 3

8-20

Freescale

Semiconductor

General Configuration Registers

DDR_ERR_EN

DDR Error Interrupt Enable

Interrupt disabled

Interrupt enabled

DMA_ERR_EN

DMA Error Interrupt Enable

Interrupt disabled

Interrupt enabled

—

Reserved. Write to zero for future compatibility.

CE_IECC_EN

ECC Error Interrupt of the QUICC Engine IMEM Enable

Interrupt disabled

Interrupt enabled

CE_DECC_EN

ECC Error Interrupt of the QUICC Engine DRAM Enable

Interrupt disabled

Interrupt enabled

TDM_P1ECC_EN

Parity Error Interrupt of TDM[4–7] Enable

Interrupt disabled

Interrupt enabled

TDM_P0ECC_EN

Parity Error Interrupt of TDM[0–3] Enable

Interrupt disabled

Interrupt enabled

TDM7_TERR_EN

TDM7 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM7_RERR_EN

TDM7 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM6_TERR_EN

TDM6 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM6_RERR_EN

TDM6 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM5_TERR_EN

TDM5 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM5_RERR_EN

TDM5 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM4_TERR_EN

TDM4 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM4_RERR_EN

TDM4 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM3_TERR_EN

TDM3 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM3_RERR_EN

TDM3 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM2_TERR_EN

TDM2 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM2_RERR_EN

TDM2 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM1_TERR_EN

TDM1 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM1_RERR_EN

TDM1 Receive Error Interrupt Enable

Interrupt disabled

Interrupt enabled

TDM0_TERR_EN

TDM0 Transmit Error Interrupt Enable

Interrupt disabled

Interrupt enabled

Table 8-15. GIER2_x Bit Descriptions

Name

Description

Settings

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MSC8144E

Reviews:

Related manuals for MSC8144E

Brands by name

Popular brands

Freescale Semiconductor MSC8144E, Reference Manual

Search results

Summary of Contents for MSC8144E

Reviews:

Related manuals for MSC8144E

Brands by name

Popular brands