manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

11-12

 Freescale 

Semiconductor

Internal Memory Subsystem

11.4.4   L2 ICache Register Block

This block contains L2 ICache registers which are configured through the MBus. These registers control: 

„

Sweep (invalidate) operation by address range or global sweep.

„

Way locking by boundaries or global. 

„

The ICache memory on/off condition.

„

Debug mode on/off and registers for reading during debug.

„

Pre-Fetch on/off. 

„

User configured burst size for accesses from L2 ICache fetch unit toward higher level 
memory. 

Note:

See Section 11.8.1 through Section 11.8.8 for register details and programming 
model.

11.4.5   Global Attributes Support 

Global attributes are used as additional external access attributes. These attributes are determined 
per MMU segment descriptor and are issued to the system. For the L2 ICache, these signals can 
be used to determine the cache policies. 

11.4.6   Functional Mode of Operation

This is the normal processing state in which each DSP core subsystem freely executes 
instructions, and initiates memory accesses.

11.4.6.1   Enabling the L2 ICache

The CLASS does not return request acknowledge signals during reset. Therefore, the L2 ICache 
cannot respond to core requests during reset. After reset, the L2 ICache is in non-cacheable mode 
only. Use the following steps to activate the L2 ICache:

1.

Exit the reset state. 

2.

Enable the two banks of the cache memory by setting the L2IC_CR2[CE] bit (see 
Section 11.8.3). 

3.

Configure the required cacheable address range in L2IC_CSA and L2IC_CEA (see 
Section 11.8.9 and Section 11.8.10), which control port 1 of the CLASS initiator. If you 
do not configure these values, the initiator uses the default values. Set the 
L2IC_CEN[DEN] bit (see Section 11.8.11) to enable the cacheable range. Because the 
default value disables the address range, you must enable the window to enable the 
cache.

4.

The L2 ICache can begin normal operation for cacheable and non-cacheable requests.

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
VAF instruments 667 Instructions For Installation, Operation And Maintenance preview
667
Brand: VAF instruments Pages: 56
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
B&B Electronics 232PCC User Manual preview
232PCC
Brand: B&B Electronics Pages: 17
Technics SH-GE90 Service Manual preview
SH-GE90
Brand: Technics Pages: 20
NCR 7702-K134 Upgrade Manual preview
7702-K134
Brand: NCR Pages: 15
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
Eastern Voltage Research Advanced Flame 1.0 Instruction Manual preview
Advanced Flame 1.0
Brand: Eastern Voltage Research Pages: 12
ADTRAN TRACER 5045 Manual preview
TRACER 5045
Brand: ADTRAN Pages: 9
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Brand: Inspired Energy Pages: 5
Renesas H8SX1664 User Manual preview
H8SX1664
Brand: Renesas Pages: 21
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
Juniper MX104 Quick Start Manual preview
MX104
Brand: Juniper Pages: 30
Gigabyte X570 AORUS ELITE WIFI User Manual preview
X570 AORUS ELITE WIFI
Brand: Gigabyte Pages: 48
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Brand: Apposite Technologies Pages: 57

Brands by name

Popular brands

Load more brands