Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 711 / 1374

background image

RapidIO Message Unit

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

16-71

7.

By reading the inbound message status register (IMxSR[MIQI]), software detects that
the message-in-queue interrupt bit is set and determines that the message-in-queue event
caused the interrupt.

8.

Software processes the frame queue entry to which the frame dequeue pointer address
registers (IMxFQDPAR) are pointing.

9.

Software increments the dequeue pointer address registers (IMxFQDPAR) by setting the
message increment bit (IMxMR[MI]). Software determines whether there are any more
messages to process by reading the queue empty bit (IMxSR[QE]). If the queue is not
empty, the previous two steps are repeated.

10.

Optionally, software reads the enqueue pointer address registers (IMxFQEPAR) and
processes all the received messages. After message processing is complete, the dequeue
pointer address registers (IMxFQDPAR) are written.

11.

Software clears the message-in-queue interrupt bit (IMxSR[MIQI]) by writing a 1 to the
IMxSR[MIQI] bit.

16.3.3.3 Message Steering

Messages are forwarded to the inbound message controllers as follows:

Messages directed to mailbox 0 are forwarded to message controller 0.

Messages directed to mailbox 1, 2, or 3 are forwarded to message controller 1.

16.3.3.4 Retry Response Conditions

The conditions to generate a logical layer retry (response retry) are as follows:

The local memory circular queue is full and a message is received.

The inbound message controller has received at least one segment of a multiple-segment
message but has not received all message segments (as determined by a different RapidIO
source ID, RapidIO destination ID, or mailbox).

A message is received with a higher priority than all previous messages being written to
memory, but it has not completed.

Note:

If all inbound messages have the same RapidIO priority, this condition for generating a
retry does not occur.

16.3.3.5 Inbound Message Controller Interrupts

The inbound message controller generates the inbound message interrupt for several different
events. Each event can be individually enabled:

Message-In-Queue interrupt is generated under one of the following conditions:

«
...
709
710
711
712
713
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: ebm-papst Pages: 16

Brand: Cypress Semiconductor Pages: 9

inLab Speedcure 9494800

Brand: Dentsply Sirona Pages: 91

Brand: Freescale Semiconductor Pages: 921

RocketCache 3240X8

Brand: HighPoint Pages: 17

Brand: ADS Technologies Pages: 21

Brand: Dave Embedded Systems Pages: 79

Brand: MCT Pages: 12

FiberTwist XGS2420

Brand: Genexis Pages: 7

Brand: ELSA Pages: 60

Brand: Helmholz Pages: 14

Brand: Telit Wireless Solutions Pages: 79

Brand: Vertilon Pages: 21

Brand: Enterasys Pages: 808

Brand: Samsung Pages: 2

Wisenet SNK-B73040BW

Brand: Samsung Pages: 65

Brand: Samsung Pages: 82

Brand: Samsung Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands