Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 670 / 1374

background image

MSC8144E Reference Manual, Rev. 3

16-30

Freescale

Semiconductor

Serial RapidIO

®

Controller

16.2.10.3 Logical Layer RapidIO Errors

This section describes how the logical layer detects and responds to RapidIO errors. The action of
the core processor when it is notified of these errors is minimally described. For details, see the
interrupt generation reference in the RapidIO Interconnect Specification, Revision 1.2, part VII
(Error Management Extensions Specifications).

Table 16-10 through Table 16-22 list all the errors detected by the RapidIO endpoint logical
layer and the actions taken. Error responses are sent as follows:

When the RapidIO endpoint action includes sending an error response to the system or the
RapidIO interconnect, an error response is sent only if the original transaction is a request
requiring a response. Otherwise, no error response is sent.

For multiple errors, a discard of a packet has a higher priority than an error response.

For misaligned transactions, the error management extension registers are updated with
each child.

Table 16-9. Physical RapidIO Threshold Response

Error

Error

Enable

RapidIO Endpoint Action

EME Error

Type

Error Detect

Interrupt

Clear

*

Notification Errors

Error rate
counter
exceeded the
degraded
threshold.

P0ERTCSR[ERDTT] > 0
and any bit in P0EECSR
enables detect and
interrupt generation.

Generate interrupt.
Continue to operate normally.

Degraded
threshold

P0ESCSR[ODE] Write 1 to

P0ESCSR
[ODE]

Fatal Errors

Consecutive
retry counter
exceeded the
retry counter
threshold
trigger

PRETCR[RET] > 0
enables detect and
interrupt generation

Generate interrupt. Port is in
priority order.

Consecutive
retry threshold

P0IECSR[RETE] Write 1 to

P0IECSR
[RETE]

Error rate
counter
exceeded the
failed
threshold.

P0ERTCSR[ERFTT] > 0
and any bit in P0EECSR
enables detect and
interrupt generation.

Generate Interrupt. Port behavior
depends on P0CCSR[SPF] and
P0CCSR[DPE]. Port can continue
transmitting packets or stop
sending output packets, keeping
or dropping them.

Failed
threshold

P0ESCSR[OFE] Write 1 to

P0ESCSR
[OFE]

Note:

Information given here is minimal for clearing the interrupt. More detailed steps should be taken to find the cause of
the interrupt, as described in the interrupt generation reference of the RapidIO Interconnect Specification, Revision
1.2 Part VII (Error Management Extensions Specifications).

«
...
668
669
670
671
672
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Yamaha Pages: 4

DR-4100P Series

Brand: Idis Pages: 30

Brand: Digitus Pages: 8

Brand: WHOOP Pages: 26

Brand: TANDBERG Pages: 3

Brand: ZALMAN Pages: 11

Brand: ASROCK Pages: 173

Brand: Rosewill Pages: 2

Brand: Thecus Pages: 148

Brand: Intel Pages: 11

Brand: IEI Technology Pages: 119

Brand: Renesas Pages: 52

Brand: C-Data Pages: 19

Brand: Idex Pages: 4

Brand: Magnescale Pages: 73

Brand: Hitachi Pages: 378

Brand: SunFounder Pages: 527

Brand: Aaeon Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands