Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1006 / 1374

background image

MSC8144E Reference Manual, Rev. 3

19-70

Freescale

Semiconductor

TDM Interface

19.7.3.7 TDMx Transmit Event Register (TDMxTER)

TDMxTER contains the status of the transmit data buffers and general transmit events.The
register can be read at any time. Bits 3–0 are cleared by writing ones to them; writing zero has no
effect.

RFSTI

4

0

Receive First or Second Threshold Interrupt Indication
Indicates whether the last receive threshold interrupt is the
first or second threshold.

0

Second threshold interrupt.

1

First threshold interrupt.

RSE

3

0

Receive Sync Error
Indicates whether a sync error has occurred. RSE is set
when the receive frame synchronization is lost (the
synchronization state change from SYNC to HUNT state)
because that a frame sync arrive early or it not recognized
at the expected position. During operation, this bit indicates
errors on the receive signals of the TDM module. For
details, see Section 19.2.4.3

0

Normal operation. No receive
error has occurred.

1

Receive sync error has occurred.

OLBE

2

0

Overrun Local Buffer Event
Indicates whether an overrun event has occurred in TDM
local memory. This error should not occur during normal
operation. It indicates that the TDM has not received
enough bandwidth on the internal MBus and therefore
cannot write the data into the destination memory (data
buffer). For details, see Section 19.2.6.

0

No overrun event has occurred in
the TDM local memory.

1

An overrun event has occurred in
the TDM local memory.

RFTE

1

0

Receive First Threshold Event
This field is set when the first thresholds of all the received
data buffers are filled with received data. The first threshold
pointer is determined by the Receive Data Buffer First
Threshold field (RDBFT). For details, see Section
19.2.6.3.

0

No receive first threshold event
has occurred.

1

A receive first threshold event
has occurred.

RSTE

0

0

Receive Second Threshold Event
This field is set when the second thresholds of all the
receive data buffers are filled with received data. The
second threshold pointer is determined by the Receive
Data Buffer Second Threshold. (RDBST) field. For details,
see Section 19.2.6

0

No receive second threshold
event has occurred.

1

A receive second threshold event
has occurred.

TDMxTER

TDMx Transmit Event Register

Offset 0x3F38

Bit

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

—

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

—

TFSTI

TSE

ULBE TFTE TSTE

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Table 19-41. TDMxRER Bit Descriptions (Continued)

Name

Reset

Description

Settings

«
...
1004
1005
1006
1007
1008
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Yaesu Pages: 2

Brand: Barco Pages: 121

Brand: MC Pages: 21

Brand: East Coast Datacom Pages: 19

Brand: Uniden Pages: 5

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

Brand: Nakayo Pages: 119

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: ebm-papst Pages: 13

Industrial Network Track OSI

Brand: GarrettCom Pages: 10

2410SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 14

Brand: Qlogic Pages: 2

Brand: FOR-A Pages: 37

Brand: WTI Pages: 178

Modular Fast Fiber Switch Converter MT-RJ

Brand: Lindy Pages: 3

AMSTX-CF Series

Brand: ADLINK Technology Pages: 73

Brand: LanReady Pages: 40

Brand: BenQ Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands