Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1055 / 1374

background image

SC3400 DSP Core Subsystem Timers

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

21-13

occurs between a timer and its TMRxCMP2 register while the Timer Compare 2 Interrupt Enable
(TCF2EN) bit is set in the TMRxCOMSC register. These interrupts are cleared by writing a zero
to the TCF2 bit in the TMRxCOMSC.

21.1.6.2

Timer Overflow Interrupts

Timer overflow interrupts are generated when a timer rolls over its maximum value while the
TCFIE bit is set in the TMRxSCTL register. These interrupts are cleared by writing a zero to the
Timer Overflow Flag (TOF) bit of the appropriate TMRxSCTL.

21.1.6.3

Timer Input Edge Interrupts

Timer input edge interrupts are generated by a transition of the input signal (either positive or
negative, depending on TMRxSCTL[IPS] setting) while the Input Edge Flag Interrupt Enable
(IEFIE) bit is set in the TMRxSCTL. These interrupts are cleared by writing a zero to the
appropriate TMRxSCTL[IEF] bit.

21.2 SC3400 DSP Core Subsystem Timers

For a detailed description of the core subsystem timers, see the MSC8144 DSP Core Subsystem
Reference Manual.

21.3 Software Watchdog Timers

Since the MSC8144E device contains four cores, there are total of five software watchdog timers
(WDTs), one per core and one for an external host. However, you can allocate the WDTs in any
manner to meet your system requirements. The five software WDTs are identical.

The WDT is responsible for asserting a hardware reset or machine-check interrupt (MCP) if the
software fails to service the software watchdog timer for a certain period of time (for example,
because software is lost or trapped in a loop with no controlled exit). Each WDT is a free-running
down-counter that generates a reset or a non-maskable interrupt on underflow. To prevent a reset,
software must periodically restart the countdown. Watchdog timer operations are configured in
the system watchdog control register (SWCRR). See Section 21.4.3.1 for details.

Note:

If any of the watchdog timers generate a reset, it resets all of the SC3400 core
subsystems in the MSC8144E device.

«
...
1053
1054
1055
1056
1057
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

UP Squared 6000 Edge Computing Kit

Brand: Aaeon Pages: 59

Brand: Jetter Pages: 35

Brand: Keithley Pages: 59

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: WAGO Pages: 48

Brand: Infoblox Pages: 13

Brand: Paradyne Pages: 6

Brand: mikroElektronika Pages: 2

Brand: RR-Concepts Pages: 12

Brand: Omron Pages: 14

Brand: Dave Embedded Systems Pages: 79

Brand: LST Pages: 1

PXI Express PXIe-1085 Series

Brand: National Instruments Pages: 89

Brand: Altronix Pages: 8

Application Module 9109 OCU-DP

Brand: Paradyne Pages: 8

AN5506-04 Series

Brand: FiberHome Pages: 146

Brand: Maco Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands