Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 964 / 1374

background image

MSC8144E Reference Manual, Rev. 3

19-28

Freescale

Semiconductor

TDM Interface

19.2.6.4 Unified Buffer Mode

When the TDMxRFP[RUBM] bit is set (see page 22-48), all receive channels are directed to one
buffer through the system interface. The number of active links must be one (RTSAL = 0b0000
or 0b0100 or 0b1100). The channel parameters of all the receive channels are located in the
TDMxRCPR0 register. Unified Buffer mode essentially creates a one-channel link that is
typically used in point-to-point connections. When TDMxTFP[TUBM] =1, data is transmitted
from one buffer into all the transmit channels.When TDMxTFP[TUBM] = 1, the first block of
data initialized for transmission in the memory is not transmitted. The size (number of bits) of the
non-transmitted block is determined by the following equation: 2

×

(TDMxTFP[TNCF] - 1)

×

(TDMxTFP[TCS] + 1). For example, if the number of transmit channels (that is,
TDMxTFP[TNCF] + 1) is 32, and the transmit channel size (that is, TDMxTFP[TCS] + 1) is 8
bits, then the number of non transmitted bits is 480. These bits (not transmitted) are located in the
TDM local memory and/or in the device level memory (M2, M3, DDR, and so forth).

Figure 19-27 describes the transmit data flow in independent data buffers mode
(TDMxTFP[TUBM] = 0). Each data channel transfers data from an independent data buffer to
the TDM local memory, and transmit data is read out serially from the local memory.

Figure 19-27. Transmit Data Buffer in Independent Data Buffer Mode (TUBM=0)

Notes: 1.

Channel 0 is a transparent channel.

2.

Channel 1 is a transparent channel
RCPR1[RCONV]=00.

3.

Channel k is an A/

μ

law channel

RCPRk[RCONV]=10.

channel (N – 1)

channel 0

channel 1

channel 2

channel 3

channel k

channel k + 1

Transmit Data Buffer

0

Transmit data Buffer

k

Transmit Data Buffer

1

TDBS

TDBS x 2

TDBS

TDMxTFSYN

TDMxTDAT

TGBA

TCPR0[TCDBA]

TCPRk[TCDBA]

TCPR1[TCDBA]

(A/m law channel)

«
...
962
963
964
965
966
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: Acconeer Pages: 32

Brand: Garland Pages: 6

Brand: Profile Pages: 6

Brand: Alesis Pages: 61

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: EVOC Pages: 57

PISO-725 Series

Brand: ICP DAS USA Pages: 8

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

Brand: Intel Pages: 958

Brand: Hama Pages: 25

Brand: Supermicro Pages: 131

Brand: VideoWave Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands