manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

10-12

 Freescale 

Semiconductor

MSC8144E SC3400 DSP Subsystem

10.9.6.4   Transition from Execution to Debug State 

This transition is initiated in one of the following ways: 

„

The JTAG DEBUG REQUEST instruction is requested by the host debugger through the 
JTAG TAP controller. 

„

EE0

 is asserted while configured as input (this is the default configuration of this port).

„

An OCE or DPU Debug event occurs (depends on proper configuration of the OCE and 
DPU registers) 

„

The DEBUG or DEBUGEV instruction is executed by the SC3400 core, with matching 
OCE configuration of its control registers. 

10.9.6.5   Transition from Execution to STOP State 

The DSP core subsystem can switch to the STOP state only in one of the non-protected modes 
(Exception or Normal) of the Execution state.  The transition is done by executing the STOP 
instruction by the SC3400 core. 

10.9.6.6   Transition from Execution to WAIT State 

The DSP core subsystem can switch to the WAIT state only in one of the non-protected working 
modes (Execution or Normal) of the Execution state. The transition is done by executing the 
WAIT instruction by the SC3400 core. 

10.9.6.7   Transition from STOP/WAIT to Debug state 

This transition is initiated in one of the following conditions: 

„

The JTAG DEBUG REQUEST instruction is requested by the host debugger through the 
JTAG TAP controller. 

„

The 

EE0

 port is asserted while configured as an input (the default configuration of this 

port). 

Note:

Entering Debug state is the default behavior of the OCE for the described events, but 
the OCE can be programmed to respond by entering the Execution state and process 
the event as a Debug exception. Therefore, before entering a STOP/WAIT state, make 
sure that the SC3400 core OCE is configured to exit the STOP/WAIT state and enter 
the Debug state and not the Execution state. See Section 10.9.6.8 and Section 10.9.6.9 
for details. Please refer to the Emulation and Debug (OCE) chapter in the SC3400 
DSP Core Reference Manual for OCE programming details.

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Brand: Lattice Semiconductor Pages: 13
Yamaha DX7mega128 Install Manual preview
DX7mega128
Brand: Yamaha Pages: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Brand: Yamaha Pages: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Brand: Yamaha Pages: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Brand: Yamaha Pages: 49
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Brand: Novus Pages: 44
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59

Brands by name

Popular brands

Load more brands