Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 523 / 1374

background image

General Configuration Block

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

13-3

13.1.2 Virtual NMI Generation

The global interrupt controller includes a Virtual NMI system that generates four NMI signals.
An NMI is generated by a write access of once of the SC3400 cores or by external host CPU. The
virtual NMI system does not have a status register.

13.2

General Configuration Block

The general configuration block performs services for rare and debug interrupts generated
throughout the MSC8144E before they reach the SC3400 EPICs. These services include:

Generating ORed interrupt signals towards the SC3400 cores (see Section 13.2.1).

Providing an interrupt enable bit for each interrupt source for each SC3400 core (see
Section 13.5.2, General Interrupt Configuration, on page 13-15).

Providing a status bit for each interrupt source. These bits are shared for all the SC3400
cores (see Section 13.5.2, General Interrupt Configuration, on page 13-15).

13.2.1 Interrupt Groups

The general configuration block generates 4 interrupts based on the groups of ORed interrupts
described in Table 13-2. The general configuration block also routes and records the status of the
VNMIs generated by the GIC.

Table 13-2. General Configuration Block Interrupt Sources

TDM

Debug

General

Watch Dog Timer

TDM 0 Rx error

CLASS 0 overrun

M2_0 ECC error

Watch Dog Timer 0

TDM 0 Tx error

CLASS 0 watchpoint

M2_1 ECC error

Watch Dog Timer 1

TDM 1 Rx error

CLASS 1 overrun

M2_2 ECC error

Watch Dog Timer 2

TDM 1 Tx error

CLASS 1 watchpoint

M2_3 ECC error

Watch Dog Timer 3

TDM 2 Rx error

CLASS 1 error

Watch Dog Timer 4

TDM 2 Tx error

CLASS 2 overrun

TDM 3 Rx error

CLASS 2 watchpoint

Parity error from TDM[0–3]

TDM 3 Tx error

L2 ICache initiator CLASS
overrun

Parity error from TDM[4–7]

TDM 4 Rx error

L2 ICache initiator CLASS
watchpoint

QUICC Engine module DRAM
ECC error

TDM 4 Tx error

L2 ICache target CLASS overrun

QUICC Engine module IMEM
ECC error

TDM 5 Rx error

L2 ICache target CLASS
watchpoint

TDM 5 Tx error

Performance Monitor all

DMA error

TDM 6 Rx error

DDR interrupt

TDM 6 Tx error

PCI all

TDM 7 Rx error

OCeaN to MBus

TDM 7 Tx error

«
...
521
522
523
524
525
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Univerge SV8100

Brand: NEC Pages: 44

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: National Instruments Pages: 9

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: Aleratec Pages: 12

Brand: Orban Pages: 255

Brand: LevelOne Pages: 31

Brand: AXIOMTEK Pages: 58

Brand: Idis Pages: 17

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: Magma Pages: 2

Brand: Cypress Semiconductor Pages: 15

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

COM Express conga-TC87

Brand: Congatec Pages: 114

Brand: Carrier Pages: 18

Brand: Qvis Pages: 233

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands