manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

17-28

 Freescale 

Semiconductor

RapidIO Interface Dedicated DMA Controller

STFLOWLVL

27–26

0

RapidIO Transaction Flow Level
Selects a priority level for the transaction flow.
Note:

The value of this bit only applies to the external 
RapidIO interface in bypass mode (SBPATMU = 1).

00 Lowest priority transaction 

flow.

01 Medium priority transaction 

flow.

10 High priority transaction flow.

11 Reserved.

SPCIORDER

24

0

Select PCI Ordering
When set, selects PCI ordering rules, which elevates write 
priority one level above reads.
Note:

This bit is ignored unless SBPATMU is set (1).

0

PCI ordering not used.

1

PCI ordering selected.

SSME

24

0

Source Stride Mode Enable
Enables/disables source stride mode. When enabled, you 
must set the required stride size and distance in the Source 
Stride Register (SSR) for the specified channel.
Note:

This bit is ignored in basic mode (MR[EFE] is cleared 
(0).

0

Stride mode disabled.

1

Stride mode enabled.

STRANSINT

23–20

0

DMA Source Transaction Interface
After transferring the last block of data in the last link 
descriptor, if MR[EOLSIE] is set, then this bit is set and an 
interrupt is generated.
Note:

This bit is ignored unless SBPATMU is set (1) and 
the transaction is to the RapidIO interface.

1100

RapidIO interface.

1111

Local access memory.

All other values are reserved.

SREADTTYPE

19–16

0

DMA Source Transaction Type
Specifies the source transaction type.
Note:

Writing a reserved value to this field causes a 
programming error to be detected and indicated in 
SR[PE] for the specified channel.

RapidIO Interface in ATMU 
Bypass mode:

0100

NREAD.

0111

Maintenance read.

All other values reserved.

Local Address space (even in 
non-ATMU bypass mode):

0100

Read, do not snoop local 
processor.

0101

Read, snoop local 
processor.

0111

Read, unlock L2 cache 
line.

All other values reserved.

—

15–10

0

Reserved. Write to zero for future compatibility.

ESAD

9–0

0

Extended Source Address
The value depends on the mode:
• Internal RapidIO transactions: Bits 9–4 are reserved and 

bits 3–0 represent the most significant 4 bits of the 36-bit 
source address.

• RapidIO interface: Bits 9–2 represent the target ID and bits 

1–0 represent the two most significant bits of the RapidIO 
address (33–32).

Note:

This field must be cleared (0) in non-bypass mode.

Table 17-11.  SATR Field Descriptions (Continued) 

Bits

Reset

Description

Setting

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
Quatech DS-3000 User Manual preview
DS-3000
Brand: Quatech Pages: 27
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
Eaton SONiX Pm10 Technical Manual preview
SONiX Pm10
Brand: Eaton Pages: 14
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
MICROENER IM30-CV Operation Manual preview
IM30-CV
Brand: MICROENER Pages: 24
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Brand: ADTRAN Pages: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Brand: Aim Pages: 35
Extreme Networks ExtremeCloud Appliance E1120 User Manual preview
ExtremeCloud Appliance E1120
Brand: Extreme Networks Pages: 219
Cypress Semiconductor CY7C68023 Specification Sheet preview
CY7C68023
Brand: Cypress Semiconductor Pages: 9
Supermicro BPN-SAS3-116A-N10 User Manual preview
BPN-SAS3-116A-N10
Brand: Supermicro Pages: 8
Allen-Bradley SLC 5/03 Installation Instructions Manual preview
SLC 5/03
Brand: Allen-Bradley Pages: 76
THOMSON SPEEDTOUCH 110G Setup And User Manual preview
SPEEDTOUCH 110G
Brand: THOMSON Pages: 26
YASKAWA 040-1CA00 Manual preview
040-1CA00
Brand: YASKAWA Pages: 87
JCAT FEMTO Quick Start Manual preview
FEMTO
Brand: JCAT Pages: 2
Compaq ProLiant 4500 Quick Start Manual preview
ProLiant 4500
Brand: Compaq Pages: 2
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Brand: Boardcon Embedded Design Pages: 36

Brands by name

Popular brands

Load more brands