manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

873

Short Reference

Call Forwarding for External Numbers

Disabling Call Forwarding on No Reply (on an Internal Telephone)

## 96

Own number

## 61 #

Enabling Time Control for the External Number (MSN) of the Dialling Telephone (on an 
Internal Telephone))

## 96 # * 69 #

Enabling Time Control for a Special Telephone Number (on an Internal Telephone)

## 96

Own number

# * 69 #

Additional information Authorisation required

The destination number may only be an external number.
Permanent configuration is enabled.

Own number

Own phone number (number without exchange line access number 
(unaffected by a direct exchange line telephone))
The number can be omitted if call forwarding is to be configured for 
the number currently sent by the telephone.

Additional information Authorisation required

The destination number may only be an external number.
Permanent configuration is enabled.

Additional information Permanent configuration is disabled.

Own number

Own phone number (number without exchange line access number 
(unaffected by a direct exchange line telephone))

Additional information Permanent configuration is disabled.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Planet Networking & Communication IPX-2000 User Manual preview
IPX-2000
Brand: Planet Networking & Communication Pages: 121
Switch Voice BR4 User Manual preview
BR4
Brand: Switch Voice Pages: 48
Panasonic KX-NCP500 Installation Manual preview
KX-NCP500
Brand: Panasonic Pages: 142
Planet Networking & Communication IPX-2000 Quick Installation Manual preview
IPX-2000
Brand: Planet Networking & Communication Pages: 14
Planet Networking & Communication IPX-1980 Frequently Asked Questions Manual preview
IPX-1980
Brand: Planet Networking & Communication Pages: 16

Brands by name

Popular brands

Load more brands