Auerswald COMpact 5000 Operation Manual Download Page 796

Page: 796 / 932

796

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Service and Maintenance

Expanding the PBX
Purchasing and Activating Software Expansions in the Upgrade-Center

1. Open the page

Administration > Dongle releases

2. Click

Open Upgrade-Center

under

UNBLOCKING CODE FOR EXTENDED

FUNCTIONS

The Upgrade-Center opens in a separate window. The serial number of the PBX is
automatically entered and set in the

PBX System: Dongle-S/N.:

entry field. An

overview of the products available for your PBX are displayed.

3. Click

Login

4. Enter the data for your user account in the

User name

and

Password

entry fields.

5. Click

Login

6. Click the category in which you want to go shopping, or click

Display

under

All items

for this device:

The items available are displayed.

Note:

Click the image in the

Details

column to view the current expansion

level on the PBX (regarding these items).

7. Place the desired item in the shopping basket by clicking the

Order

column.

8. Once you have selected all of the items you would like, click

Shopping basket /

check out

The selected items are displayed in the shopping basket.

9. Select the payment type.

10. When you are finished making changes, click:

• Proceed to the TOB

: Before the initial order and after every change in the

General Terms and Conditions (TOB), the terms and conditions of business of
Auerswald GmbH & Co. KG must be accepted.

• Proceed to the customer data

11. Follow the additional instructions.

You will receive the order confirmation for your order and the 20-digit release codes
required for release after purchase.

12. Transmit the release codes into your PBX:

•

Payment types

Credit card

Direct debit

Invoice

: The order confirmation (with

release codes) is displayed in the Upgrade-Center at the end of the order process.
Click

Apply all release codes in the PBX with IP XXX.XXX.XXX.XXX

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands