Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 474 / 932

background image

474

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Number Presentation (Outgoing)
Suppressing Number Presentation

2. In the list field at the top, select the group in question by its name or number.

3. In the

Number presentation (outgoing)

list field, select one of the following options:

Note:

For the option

No

, the telephone service

Calling Line Identification

Restriction (CLIR2)

must be released by the network provider.

On a connection with a GSM gateway, the phone number presentation
configured in the PBX is not used because the actual phone number
presentation is directly configured in the individual GSM gateway.

On a connection with

CLIP no screening

enabled, the number presentation

defined here is not considered.

Suppressing Number Presentation

Also called number suppression. You can prevent the presentation of your own number to the
partner called (anonymous call). This feature allows you to decide before starting a call if the
number should be presented to the partner called or not. The number from your own
connection can still be transmitted to the network provider so that the charges can be calcu-
lated correctly.

Note:

For this function, the telephone service

Calling Line Identification

Restriction (CLIR2)

needs to be released by the network provider.

On ISDN telephones and system telephones Calling Line Identification
Restriction (CLIR) is done using a function key or menu (optional, see manual
for the telephone; this may also be known as identification suppressed).

Calling Line Identification Restriction (CLIR) is also possible on an analogue
T-Net telephone using the T-Net function key/men, if available (see manual
for the telephone; this may also be known as anonymous calling).

No

: The phone number is suppressed.

Standard

: Both the DDI parallel to the internal number and the MSN on the

PTMP connection are displayed on the PTP connection over which the
subscriber is called (if the subscriber is not a member of the call distribution for
this connection, the first MSN is presented).

Exchange line dependent

: The phone number to be presented is configured

separately for each external connection under

Expert

.

«
...
472
473
474
475
476
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: Matrix Pages: 124

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands