manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

105

Installation and Commissioning

Commissioning

Turning on the PBX

Commissioning

This section describes the commissioning of the PBX. This includes turning on the PBX, setting 
up the network connection between the computer and the PBX as well as logging into the web 
interface on the PBX for setting up the initial configuration. After this, you will learn how to put 
each individual end device into operation.

Turning on the PBX

Requirements:

•

PBX connected to earthing and casing closed (see chapter Installation and Commissioning 
> Preparation (COMpact 5000/R) > Connecting to Earthing)

•

Connect the PBX to a freely accessible Schuko socket.

The 

Power

 and 

Status

 LEDs light up several seconds/minutes in red and orange.

When the LEDs light up in green, the PBX is ready for operation.

Note:

If the 

Power

 LED remains continuously lit in red, an error has occurred. 

Please contact your dealer or the manufacturer directly.

Switching off and powering down the PBX is described in detail in the chapter 
Service and Maintenance > Powering Down and Switching Off.

Warning:

 Touching voltage-carrying conductors or telephone connections 

can cause life-threatening electric shocks.

•

Close the casing before you put the PBX into operation.

Note: 

If you have a USB memory stick with a configuration for automatic 

loading (auconfig.cfg), insert it into the USB socket (USB host) of the CPU 
module before you switch on the PBX. The configuration data stored on the 
USB memory stick will automatically be saved to the PBX after switching 
on. The PBX restarts afterwards.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Nortel Communication Server 1000M Installation And Configuration Manual preview
Communication Server 1000M
Brand: Nortel Pages: 122
Digium AA50 Administration Manual preview
AA50
Brand: Digium Pages: 87
XONTEL Plus PBX User Manual preview
Plus PBX
Brand: XONTEL Pages: 118

Brands by name

Popular brands

Load more brands