manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

498

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Call Restrictor (outgoing) – Restricted Numbers
Switching the Call Restrictor (Outgoing) On/Off for Subscriber

Call Restrictor (outgoing) – Restricted Numbers

In order to restrict exchange line authorisation, the phone numbers that should not to be dialled 
can be put in call restrictors. There are several ways to do this. In general, phone numbers are 
restricted that begin with a certain digit sequence and that should not be accessible to every 
subscriber due to its higher charge tariffs, e.g., 0900 phone numbers. Normally, the first 4 to 5 
digits indicate the telephone service that cause such high charges.

If an attempt is made to dial a restricted phone number, only a busy signal is heard. If the 
restricted numbers are not enabled (meaning "not restricted"), restriction via the configured 
exchange line authorisation is still possible.

Switching the Call Restrictor (Outgoing) On/Off for Subscriber

If a call restrictor (outgoing) is enabled for a subscriber, the subscriber can not dial the phone 
numbers entered in the call restrictor irrespective of his exchange line authorisation.

For a single subscriber, the configuration can be made for business and private calls 
separately.

Proceed as follows:

•

Separately for subscribers

Note:

 If differently configurable functions for private and business calls are 

enabled, two different configurations can be created for each subscriber – 
one for private calls and one for business calls (see also chapter Functions > 
Private (Personalised) Exchange Line Access > Switching Differently Config-
urable Functions for Private and Business Calls On/Off).

•

Separately for configurations

•

For the exchange line transfer function (

Settings > Basic settings > EXCHANGE LINE 

CALL TRANSFER > Exchange line settings for the manually switched exchange line 
access > Configure special exchange line settings > Configure

)

•

For the Call Through function (

Functions > Call Through > EXCHANGE LINE SETTINGS 

> Configure

)

•

Using the configuration manager

Note:

 As described in the following, the setting is also possible via profiles (

... 

> Profiles > Configuration > Configure > ...

). If the check box 

Profile-

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Panasonic KX-TDE100 Getting Started preview
KX-TDE100
Brand: Panasonic Pages: 32
Panasonic KX-TDE100 Product Catalog preview
KX-TDE100
Brand: Panasonic Pages: 29
Panasonic KX-TDE100 Pc Programming Manual preview
KX-TDE100
Brand: Panasonic Pages: 982
Panasonic KX-TDE100 User Manual preview
KX-TDE100
Brand: Panasonic Pages: 254
Panasonic KX-TDE100 Pt Programming Manual preview
KX-TDE100
Brand: Panasonic Pages: 62
Panasonic KX-TDE100 Features Manual preview
KX-TDE100
Brand: Panasonic Pages: 460

Brands by name

Popular brands

Load more brands