Auerswald COMpact 5000 Operation Manual Download Page 336

Page: 336 / 932

336

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Call Through
Switching LCR for Call Through Calls On/Off

2. Configure the call assignment. Doing this also specifies over which external number

the Call Through user calls the Call Through function and how many Call Through
calls can be made simultaneously.

3. Create the desired Call Through user. When you do this, add the corresponding

phone number as contact to the address book and select the conact as Call Through
user.

Note:

Call Through is automatically configured for each of the four phone

numbers that can be entered for each contact, but only for a total of 400
contacts.

Switching LCR for Call Through Calls On/Off

If LCR for Call Through calls is enabled, even for Call Through calls the most cost-effective
telephone service provider is determined.

Proceed as follows:

•

Using the configuration manager

1. Open the page

Functions > Call Through

2. Select or clear the

LCR for Call Through calls

check box under

EXCHANGE LINE

SETTINGS

Configuring the Maximum Duration for External Call Through Calls

Due to security reasons, external Call Through calls from the PBX have a time limit.

Proceed as follows:

•

Using the configuration manager

LCR for Call Through calls

Maximum duration for external Call Through calls

Exchange line settings for Call Through calls

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands