manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

496

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Switch Input
Creating a Switch Input

Switch Input

If a device that is suitable as switch input (e. g. a door terminal with door bell buttons) is 
connected to the PBX, it can then be used to trigger a door call or an alarm.

Creating a Switch Input

Switch input connected to the PBX which are to be used to initiate a door call or trigger an alarm 
must first be created in the configuration of the PBX.

Proceed as follows:

•

Separately for alarms (see chapter Functions > Alarm > Creating a Switch Input and 
Assigning it to the Alarm)

•

Separately for door terminals (see chapter Functions > Door Functions > Creating a Door 
Call and Assigning it to the Door Terminal)

Entering the DTMF Sequence

The PBX can detect the actuation of a door bell button, for example, and then trigger an alarm 
or a door call. To detect the actuation of a door bell button, the PBX needs to know which DTMF 
sequence the connected device sends in this case (see manual and settings of the device in 
question).

Note:

 The DTMF sequence usually is the phone number assigned to the door 

bell button within the door terminal.

Proceed as follows:

•

Separately for switch inputs

•

Using the configuration manager

Requirements:

•

Created analogue switch input

1. Open one of the following pages:

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Digium Switchvox AA355 Quick Start Manual preview
Switchvox AA355
Brand: Digium Pages: 2
Nokia 22 Operator'S Manual preview
22
Brand: Nokia Pages: 54
Panasonic KMS1409096CE Service Manual preview
KMS1409096CE
Brand: Panasonic Pages: 191

Brands by name

Popular brands

Load more brands