Auerswald COMpact 5000 Operation Manual Download

Page: 430 / 932

430

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Online Name Search
Creating Service Providers Manually

Downloading Provider Data via an existing connection between the PBX and the Internet

Requirements:

•

PBX with an existing Internet connection

1. Open the page

Functions > Online name search > Basic settings

2. Click

Online service provider

3. Select the desired provider from the list field and click

Download

The provider data are downloaded, and the provider is displayed under

Service

provider

Downloading Provider Data via an existing connection between the PC and the Internet

Requirements:

•

PC with an existing Internet connection

1. Open the page

Functions > Online name search > Basic settings

2. Click

Online service provider

3. In the

Provider

list field, select the desired provider.

4. Click

Download

The dialogue for downloading the provider file (*.n2n) appears.

5. Save the file on the PC.

Further steps:

•

Import the downloaded provider data into the PBX.

Creating Service Providers Manually

The service provider list accommodates up to five service providers, who can be imported or
created manually.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands