Auerswald COMpact 5000 Operation Manual Download Page 190 | Manualshive

Page: 190 / 932

background image

190

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Address Books and Lists

Address Books
Creating a Contact Group

Note:

Subscribers with Telephone book authorisation and read access to the

Telephone book version 1

contact group can dial exchange line numbers,

even if they have no other exchange line authorisation.

In addition, administrators and sub-administrators can create their own contact groups and
assign types to them. These types set the possible size of the contact group and specify the
telephones to which the contacts in this contact group are to be transmitted . You can assign
the following types to the contact groups:

• Standard contact group

: contact groups for the COMfortel 1400 IP/2600 IP/3200/3500/

3600 IP and COMfortel 1200/1400/1600/2600 system telephones with a maximum of 2000
contacts. Contacts that are assigned to contact groups of this type are displayed on the
connected COMfortel 1400 IP/2600 IP/3200/3500/3600 IP and COMfortel 1200/1400/1600/
2600 system telephones.

• DECT 900 contact group

: contact groups for COMfortel DECT 900 handsets with a

maximum of 140 entries. Contacts that are assigned to contact groups this type are
displayed on the connected COMfortel DECT 900 handsets. They must also be contained
in the

Telephone book version 1

contact group.

• DECT 900C contact group

: contact groups for COMfortel DECT 900C handsets with a

maximum of 250 entries. Contacts that are assigned to contact groups of this type are
displayed on the connected COMfortel DECT 900C handsets. They must also be contained
in the

Telephone book version 1

contact group.

Note:

The contacts contained in the contact groups of the type

DECT 900 contact

group

and

DECT 900C contact group

must also be contained in the

Telephone book version 1

contact group.

Only one type can be selected per contact group. It is not possible to change
the contact group type afterwards.

If you have not selected a type, the

Standard contact group

type is automat-

ically assigned to the new contact group.

Creating a Contact Group

To get a better overview of the contacts displayed in

All contacts

view you can create up to 20

contact groups, each of which represents a sub group of the

All contacts

view.

«
...
188
189
190
191
192
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: IP Cortex Pages: 36

Pro series Hybird 120

Brand: Gigaset Pages: 423

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands