manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

241

Voice Mail and Fax Boxes

Voice Mailbox

Switching Automatic Clean-up of a Voice Mailbox On/Off

4. Enter a value in the 

Maximum length per recording

 entry field under 

Maximum 

recording capacity

. Possible entries:

Switching Automatic Clean-up of a Voice Mailbox On/Off

The number of stored messages is limited to 999 per box and 100,000 in the system. If the 
automatic clean-up of a box is enabled and the maximum number of stored messages or the 

Maximum recording capacity

 of the box is reached, the oldest messages marked as read will 

be deleted as soon as new messages arrive. Archived messages will not be deleted.

Proceed as follows:

•

Separately for voice mailboxes

•

Using the configuration manager

Requirements:

•

Voice mail/fax function (optional, see chapter Important Information > Product Details > 
Basic Assembly and Extensions)

1. Open the page 

Devices > Voice mail/fax boxes > Properties > Box settings

.

2. In the list field at the top, select the voice mailbox in question according to the name 

or number.

3. Select or clear the 

Perform at ...

 check box under 

Automatic clean-up

.

4. If you have enabled automatic clean-up, enter a value in the 

... memory utilisation

 

entry field. Possible entries:

15

 to 

999

: The recording capacity of the box is 15 to 999 MB. 

No value: The recording capacity is unlimited (maximum memory utilisation).

1

 to 

99

: The length per recording in the box is 1 to 99 minutes. 

No value: The length per recording is unlimited (maximum memory utilisation).

50

 to 

95

 percent.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

LV switch IPPBX8000 User Manual preview
IPPBX8000
Brand: LV switch Pages: 199
Panasonic KX-T7565 User Manual preview
KX-T7565
Brand: Panasonic Pages: 296
InnoMedia iPBX-400 Administrative Manual preview
iPBX-400
Brand: InnoMedia Pages: 104

Brands by name

Popular brands

Load more brands