Auerswald COMpact 5000 Operation Manual Download Page 767 | Manualshive

Page: 767 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

767

Service and Maintenance

Remote Configuration and Alternative Connection Options

Configuring the PBX Remotely via the Internet (without ARA server)

The login window of the configuration manager opens.

8. Log in to the configuration manager.

9. Make the desired changes.

10. Log out from the configuration manager.

11. Click

in the user interface of the ARA server.

Configuring the PBX Remotely via the Internet (without ARA server)

Requirements:

•

Internet connection between the computer and the PBX (for example, DSL)

•

Permanent external IP address, or the use of VPN or DynDNS

•

A router configured for this purpose

•

Knowledge of user name and password for the configuration manager

•

Knowledge of the configured port of the web server

Note:

Refer to the operating manual of your router.

The access is possible via

http:

and via

https:

(encrypted access). If the

option

Force HTTPS connection

has been enabled, only the https

connection can be used. In this case, a port you selected yourself must be
rerouted to port 443 of the PBX (access with

https://

mein.dyndns.org:[port]

, for example).

Important:

An internal network is usually protected from actions from the

outside by, for example, a firewall integrated in the router. For questions
about configuring your firewall, contact the system administrator responsible
for this topic.

1. Start a browser (for example, Mozilla Firefox).

2. Enter

http://

and the external IP address for the PBX as well as the

:

character, and

then the port, into the address field of the browser.

The login window opens.

«
...
765
766
767
768
769
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands