Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 698 / 932

background image

698

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

Call Distribution
Configuring the Modem/Fax Call Distribution for Analogue Connections

Note:

The overview can be viewed and printed (

Print

) in the configuration

manager by opening the page

Overview > Call distribution

.

Configuring the Modem/Fax Call Distribution for Analogue Connections

If the modem/fax call distribution is enabled, the PBX transfers external calls actively or
passively to an internal terminal device.

If the active modem/fax call distribution is enabled, the PBX automatically accepts every
external call to the corresponding phone number. Using the dial tones, it attempts to determine
whether the incoming call is from a fax machine or from a modem. If the corresponding dial
tones are identified within the detection time frame configured, the call is forwarded to the
selected internal number (subscriber, group, voice mail/fax box).

If the passive modem/fax call distribution is enabled (), an external call is transferred to an
internal subscriber via the normal call distribution. If the user accepts the call and ends it within
the configured detection time frame, the call is automatically transferred to the internal desti-
nation selected in the last column (subscriber, group, fax box).

Proceed as follows:

•

Using the configuration manager

Configuring Active Modem/Fax Call Distribution for Analogue Connections

Requirements:

•

External analogue port (optional, see chapter Important Information > Product Details >
Basic Assembly and Extensions)

•

Entered phone number

•

Created internal destinations (subscribers, groups, fax boxes)

1. Open the page

Public switched tel. networks > Call distribution

.

If several configurations (PBX profiles) have been created, these will be available as
tabs.

2. With several configurations: Click the tab with the desired configuration.

«
...
696
697
698
699
700
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Quadro Quadro 2xi

Brand: Epygi Pages: 2

Brand: AVM Pages: 80

Brand: Panasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands