manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

638

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

VoIP
VoIP Provider Settings

Note:

 During sub-system operation, single-digit dialling may cause 

problems. In this case, en-bloc dialling is usually enabled.

Connect audio through

 

 The connection between the caller and the PBX is always created when a call is forwarded 

externally. As a result, the caller will hear all replayed elements (tones, announcements) which 
are played by the VoIP provider when the connection with the call forwarding destination is 
established.

 If external call forwarding is configured over a VoIP provider, the call tone may not be 

replayed for the caller (the connection to the call forwarding destination number will therefore 
be switched through in a "surprising" way).

Support T.38 for providers

 

T.38 negotiation

 

Requirements:

•

external VoIP channel that supports T.38 (optional, see Important Information > Product 
Details > Basic Assembly and Extensions section)

•

VoIP provider support for T.38

•

Configured internal fax subscribers

 T.38 (procedures for real-time Group 3 facsimile communication over IP networks) enables 

smooth, extensive fax transmission to take place.

Note:

 If problems occur when T.38 is switched on, you can change the setting 

used to negotiate the fax protocol (

T.38 negotiation

).

Compliant to RFC

: two separate media lines for disabling audio and negotiating the fax 

protocol.

Variant 1

: only one media line for negotiating the fax protocol (the media line for disabling audio 

is not used).

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Quadro QUADRO4LI Administrator'S Manual preview
QUADRO4LI
Brand: Quadro Pages: 122
Telesis PX24X Manual preview
PX24X
Brand: Telesis Pages: 48
Telstar Electronics SkyWave DX600 Assembly Manual preview
SkyWave DX600
Brand: Telstar Electronics Pages: 57

Brands by name

Popular brands

Load more brands