Auerswald COMpact 5000 Operation Manual Download

Page: 174 / 932

174

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Address Books and Lists

Address Books
Deleting a Contact Person's Image

Deleting a Contact Person's Image

Proceed as follows:

•

Using the configuration manager

Requirements:

•

For users: write access to at least one contact group

1. Open the following page:

•

As administrator:

User data > Address books > Contacts & assignment

•

As a user:

Contacts & assignment

All contacts

view appears.

2. Limit your search:

•

By contact group: click a contact group.

•

Using the filter: enter at least one character or one digit in the

Filter

line in one or

more of the entry fields.

•

Using the tabs: click

All

Contacts without contact groups

, or an initial letter.

3. In the line that contains the required contact, click

4. Click

Delete image

The image is deleted from the image window. However, the image file for the image
remains in the folder from which the image was imported.

Editing a Contact

You can view a contact that has been created in the PBX and then edit it.

Proceed as follows:

•

Using the configuration manager

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands