manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

611

Settings

ISDN Connection

PTP Connection Settings

PTP Connection Settings

Proceed as follows:

•

Separately for PBX base numbers

•

Using the Configuration Manager (page 

Public switched tel. networks > ISDN connec-

tions > PBX base numbers/trunk bundles > Configure

)

Requirements:

•

Configured PBX base number

NETWORK PROVIDER

Exchange line has emergency call ability

 

Requirements:

•

The corresponding connection must allow emergency calls

 This exchange line can be used for emergency calls.

 This exchange line cannot be used for emergency calls. When you attempt to dial an 

emergency number, you will hear the announcement, "This telephone does not allow 
emergency calls. Please use an alternative."

Note:

 If you have updated your firmware from Version 6.4 to 6.6, the 

telephone allows emergency calls by default.

CCBS

 

Requirements:

•

Service feature CCNR (callback on no response) is enabled by the network provider.

•

Configured prefixes (country prefix and local area code)

 The PBX offers the callback option to an external caller if the connection they dialled is busy.

Important:

If this function is enabled, but the network provider does not support it 
(service feature not unlocked), it might still happen that the caller is given the 
option of a callback. In this case, the caller's reply is not forwarded to the PBX 
and therefore the function cannot be performed.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Nokia 22 Operator'S Manual preview
22
Brand: Nokia Pages: 54
Panasonic KX-NS700 Feature Manual preview
KX-NS700
Brand: Panasonic Pages: 580
Aastra AastraLink RP 500 Installation Manual preview
AastraLink RP 500
Brand: Aastra Pages: 16

Brands by name

Popular brands

Load more brands