Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 631 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

631

Settings

VoIP

VoIP Provider Settings

Time limit for registration (1 to 60 min.)

The registration time specifies how many minutes the PBX waits before reregistering itself with
the VoIP provider.

Note:

In the test phase, after configuring the VoIP provider, we recommend

you enter a low value (e.g. three minutes). After completing the test phase,
you can enter a much higher value, since some VoIP providers also reject
calls if too many attempts are made to register.

SIP registration in accordance with RFC 6140

The PBX complies with the SIPconnect 1.1 SIP protocol.

NAT traversal

NAT (Network Address Translation) enables you to convert a particular IP address that is used
within a network (e.g. a local network) into a different IP address that can be used by a different
network (e.g. the public switched telephone network). If NAT traversal is switched on, and a
query is sent from a local IP address to the public network, the sending IP address is swapped
with the public IP address. This function is performed in the reverse direction for the reply.

Disabled

: NAT traversal is not performed by the PBX. The router which connects the local area

network with the Internet should be a properly functioning, SIP-aware router which performs
NAT traversal.

Enabled with use of STUN

: NAT traversal is performed by the PBX. To achieve this, a STUN

server must also be specified for the VoIP provider.

Enabled

: NAT traversal is performed by the PBX. To achieve this, the registrar for the VoIP

provider must be switched on. The SIP request also contains an "rport" part in which the IP
addresses used here (local, public) are transported.

Notes:

If

Enabled

is selected: If problems occur with single-sided call connections,

use

Enabled with use of STUN

instead.

Caution:

Each time a port is opened on the router, this creates a

potential source of danger.

•

It is essential you put additional protective measures in place.

«
...
629
630
631
632
633
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: ATCOM Pages: 35

Brand: Far south networks Pages: 19

Brand: Panasonic Pages: 32

Brand: Tokyo Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands