Auerswald COMpact 5000 Operation Manual Download Page 822 | Manualshive

Page: 822 / 932

background image

822

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Short Reference

Short Reference

This section includes an alphabetical list of functions and settings of the PBX you can configure
using an internal or, in some cases, an external telephone. The functions available in the menu
of the system telephones as well as the menu functions or keys used by individual ISDN
telephones are not listed (see manual for the telephone).

The headlines explain which device may be used for the named character string. If the column
is limiting the character string (e.g. for starting a conference) to analogue telephones only it
may be available to ISDN telephones via menu (see manual of the telephone).

Is the function also available to external devices a remote switching number configured in the
PBX has to be dialled first.

Topics

–

Alarm (page 824)

–

Reservation of Exchange Line on Busy (page 827)

–

Call Waiting (page 828)

–

Time and Date (of the PBX) (page 829)

–

Do-not-Disturb (page 830)

–

Automatic Reception (page 831)

–

Baby Call/Hotline (page 832)

–

Call Through (page 833)

–

Remote Configuration (Releasing) (page 834)

–

Hook Flash Timing (page 835)

–

Follow-me (page 836)

–

Call Restrictor (Incoming) (page 879)

–

Call Allowance Account (page 839)

–

Outgoing Calls (page 840)

–

Call Data (Single Call Record) (page 841)

–

Targeted Exchange Line Access (page 842)

–

Targeted VoIP Access (page 843)

–

Groups (page 844)

–

Hotel Functions (page 846)

–

Identification (IPv4 Address, Subnet Mask, Gateway, DHCP Client) (page 847)

–

InterCom Announcement/Handsfree Speaking (page 849)

–

Conference (page 850)

–

Configuration Switchover (page 851)

–

Loudspeaker Announcement (page 852)

–

Emergency Call Announcement (page 853)

–

Call Parking (page 854)

–

Multi-Path Call Forwarding (page 855)

«
...
820
821
822
823
824
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: H3C Pages: 514

TC-2000 AK Series

Brand: CTI Pages: 65

Brand: Telstar Electronics Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands