manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

844

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Short Reference

Groups

Groups

Logging in to a Group (Incoming and Outgoing - on an Internal Telephone)

## 8 * 40 1

Group number

#

Logging out of a Group (Incoming and Outgoing - on an Internal Telephone)

## 8 * 40 0

Group number

#

Logging out of All Groups (Incoming and Outgoing - on an Internal Telephone)

## 8 * 40 0 #

Logging in to a Group (Only Incoming - on an Internal Telephone)

## 8 * 41 1

Group number

#

Logging in to All Groups (Only Incoming - on an Internal Telephone)

## 8 * 41 1 #

Logging out of a Group (Only Incoming - on an Internal Telephone)

## 8 * 41 0

Group number

#

Logging out of All Groups (Only Incoming - on an Internal Telephone)

## 8 * 41 0 #

Group number

Internal number of the group (for exchange line request type Direct 
exchange line telephone: with preceding **)

Group number

Internal number of the group (for exchange line request type Direct 
exchange line telephone: with preceding **)

Group number

Internal number of the group (for exchange line request type Direct 
exchange line telephone: with preceding **)

Group number

Internal number of the group (for exchange line request type Direct 
exchange line telephone: with preceding **)

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

JK Audio PBXport User Manual preview
PBXport
Brand: JK Audio Pages: 16
JK Audio Innkeeper PBX User Manual preview
Innkeeper PBX
Brand: JK Audio Pages: 20
Fiberme FAG410X Manual preview
FAG410X
Brand: Fiberme Pages: 15

Brands by name

Popular brands

Load more brands