manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

44

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Important Information

Product Details
Installation

Switch Input

The PBX can only be extended with switch inputs by connecting the corresponding acces-
sories. See Ethernet port and internal analogue port.

Announcement Output

The PBX can only be extended with announcement outputs by connecting the corresponding 
accessories. See Ethernet port and internal analogue port.

Installation

The PBXs are intended to be operated in closed rooms. In addition, all of the devices 
connected to the system must be located inside the building.

The PBXs enable you to connect some devices directly, inasmuch as they are close enough to 
the PBX. The distance depends on the length of the equipment connection cables up to a 
maximum of 10 m.

If no suitable connection sockets are available or are too far away, you must lay the installation 
cable permanently.

Warning:

 Power surges, which can occur during electrical storms, can 

cause life-threatening electric shocks.

•

Hire a qualified electrician to lay the cables within the building – including 
the cable to the door terminal.

•

Do not use the a/b ports to connect remote extensions.

Important:

 Improper use can cause, for example, functional restrictions or 

interference, the destruction of the device or, in a worst-case scenario, 
personal injury.

•

Only connect equipment that is compatible with the proper use of the 
PBX.

Note:

The terminal clamps on the modules are removable to facilitate installation.
Accessories and service parts can be bought at specialised stores or in the 
Internet shop distriCOM (see 

www.districom.de

). Delivery is provided only 

in Germany and for specialised dealers also to Austria.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Yeastar Technology MyPBX User Manual preview
MyPBX
Brand: Yeastar Technology Pages: 133
Far south networks Com.X1 PBX User Manual preview
Com.X1 PBX
Brand: Far south networks Pages: 19
Panasonic KX-TD500 Quick Reference Manual preview
KX-TD500
Brand: Panasonic Pages: 4
Yeastar Technology S20 Installation Manual preview
S20
Brand: Yeastar Technology Pages: 12

Brands by name

Popular brands

Load more brands