Auerswald COMpact 5000 Operation Manual Download

Page: 469 / 932

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

469

Functions

Call Channel Reservation

Switching Call Channel Reservation On/Off

4. In the

Number

list field, select how many B channels of the external connection

should be reserved. These B channels are never available to the other subscribers or
groups.

Note:

If a channel should be reserved for one subscriber this subscriber has to be
assigned alone to a group.

A B channel reserved for a group is only available for the members of the
group who are logged in the group outgoing.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands