Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 509 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

509

Functions

Announcement before Answering

Switching Announcement before Answering On/Off

Announcement before Answering

This function allows a greeting message to be played to the caller before accepting the call and/
or if all group members are busy.

The call is first accepted by the PBX (the external caller is charged from now on). The external
caller hears the announcement before answering (e.g., with information about the company).
Afterwards, the caller hears Music on Hold or the call tone again (if the line is bus, he is put into
the waiting loop after the announcement until the call is answered). As soon as one of the called
telephones accepts the call (or if busy, finishes the call before that), he is connected to the
external caller.

After the announcement before answering, the caller is put on hold by the PBX for max. 8
minutes. If the call is not taken within these 8 minutes, it is disconnected. The on hold time is
reduced if internal subscribers are ringing but not taking the call. Then the caller is rejected after
less than 8 minutes.

Proceed as follows for configuration:

•

Managing and assigning audio files for announcements.

–

Using the configuration manager (on the following pages)

– Functions > Music on Hold/Announcements > File management
– Functions > Music on Hold/announcements > File assignment > Ann. before

answering

–

Using a character string on the internal telephone (see section Short Reference)

•

Configuring text before answering.

–

Using the configuration manager (page

Groups > Properties > Reachability

)

•

Switching text before answering on/off.

–

Using the configuration manager (page

Groups > Properties > Reachability

)

–

Using the menu/function key on a system telephone (optional, see the telephone
manual)

•

Switching text before answering for fallback on/off.

–

Using the configuration manager (page

Public switched tel. networks > Call distri-

bution

)

Switching Announcement before Answering On/Off

If announcement before answering is enabled, in external group calls a greeting message is
played to the caller before accepting the call and/or if all group members are busy.

«
...
507
508
509
510
511
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Quadro Quadro 4x

Brand: Epygi Pages: 2

Brand: XonTel Technology Pages: 117

Brand: Vaid Systems Pages: 60

Brand: Panasonic Pages: 204

Brand: Digium Pages: 87

Brand: SMC Networks Pages: 132

Brand: New Rock Technologies Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands