manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

338

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Call Through
Configuring Call Assignments

Configuring Call Assignments

In call assignment you can specify which external number the Call Through user dials to access 
the Call Through function, and how many simultaneous Call Through calls are permitted.

Proceed as follows:

•

Using the configuration manager

Requirements:

•

External numbers have been entered

•

To use VoIP numbers: 

Standard (use of From headers als Screened Number)

 

configured for the VoIP provider as evaluation type of incoming SIP messages (see chapter 
Settings > VoIP Provider > Configuring the Evaluation of Incoming SIP Messages)

1. Open the page 

Functions > Call Through

.

2. In the 

Call Through number

 list field under 

CALL ASSIGNMENT

, choose the 

external number that the Call Through user must dial to call the PBX for Call Through.

Note:

 Call Through numbers are not included in call distribution and cannot 

be diverted.

3. In the 

Max. number

 list field under 

CALL ASSIGNMENT

, select one of the following 

options:

Creating Call Through Users

The phone numbers on the mobile phone (call through user) which are used to carry out the 
Call Through function must be entered under 

Address books

. The corresponding contacts 

must then be selected as Call Through users. In addition, it can be configured whether the 
phone number dialled by the Call Through user should be checked to see if it is a call restrictor 
or call deblocker number.

—

 No Call Through calls are permitted.

Value, e.g. 

1

 and 

2

: The selected value specifies the maximum number of Call 

Through calls.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Karel DS200 Installation Manual preview
DS200
Brand: Karel Pages: 39
H3C XE 200 IP Operation Manual preview
XE 200 IP
Brand: H3C Pages: 514
Excelltel CDX-CS User Manual preview
CDX-CS
Brand: Excelltel Pages: 48
Excelltel MK-208 User Manual preview
MK-208
Brand: Excelltel Pages: 64

Brands by name

Popular brands

Load more brands