Auerswald COMpact 5000 Operation Manual Download Page 367

Page: 367 / 932

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

367

Functions

Hotel Function

Configuring the Print Quality

Proceed as follows:

•

Using the configuration manager

Requirements:

•

For using the print option: Printer connected to the PBX (PCL4-compatible (HP Laserjet))

•

For using the print option: Configured reception telephone

1. Open the page

Functions > Hotel function > Create print form

2. Select or clear the

Activate print options

check box.

Configuring the Print Quality

This function serves to determine the font quality of the telephone bill.

Proceed as follows:

•

Using the configuration manager

Requirements:

•

For using the print option: Printer connected to the PBX (PCL4-compatible (HP Laserjet))

•

For using the print option: Configured reception telephone

•

For using the print option: Enabled print option

1. Open the page

Functions > Hotel function > Create print form

2. In the

Print quality

list field, select one of the following options:

Configuring the Number of Printouts

The amount of invoices to be printed out (original do copies) can be configured here
(1 to 4 printouts).

Draft

: Fast print in draft quality.

Letter

: Invoice in letter quality, i.e. in calligraphy.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands