manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

342

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Follow-me
Configuring Follow-me

Requirements:

•

Authorisation for 

CF (groups) / Follow-me

•

Authorisation for 

Controlling of the PBX via telephone

•

For internal destination: Minimum requirement - exchange line authorisation 

Only 

incoming, with emergency call

 to accept forwarded external calls

•

For call forwarding to an external number: Authorisation 

Configuring CF (sub) to ext. 

number

•

For call forwarding to an external number: The external destination must be reachable for 
the subscriber (minimum requirement: Exchange line authorisation 

National

, selected call 

restrictor under Exchange line settings 

Call restrictor (outgoing) - business

 does not 

restrict the selection of the external destination)

•

For configuring Follow-me externally: Knowledge of the Remote switching number for 
remote programming and PIN (External PIN)

– For configuring Follow-me externally: DTMF dialling at the configuring device

1. Open one of the following pages:

•

for subscribers: 

Subscriber (scr.) >Properties > Reachability

•

for groups: 

Groups > Properties > Reachability

2. In the list field at the top, select the subscriber/group in question by name or number.

3. In the 

Destination number

 entry field under 

Follow-me (internal/external)

 enter the 

destination number. Possible entries:

4. Click 

 

Save

, to enable 

Follow-me (internal/extern)

.

Note:

 Delete the destination number to switch off 

Follow-me (internal/

external)

.

External number

Short-code number

Internal number of the individual telephone

Internal number of the line group

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

NEC SL1100 Adminstrators Manual preview
SL1100
Brand: NEC Pages: 33
NEC ASPILA EX Hardware Manual preview
ASPILA EX
Brand: NEC Pages: 186

Brands by name

Popular brands

Load more brands