manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

UART/IrDA Control and Status Registers

 

12-72

Table 12–64. XOFF2 Register (XOFF2)

Bit

Name

Function

R/W

Reset

Value

7–0

XOFF_WORD2

Used to store the 8-bit XOFF2 character in used
in UART mode.

R/W

0x00

The scratchpad register (SPR) does not control the module in anyway. It is a
scratchpad register to be used by the programmer to hold temporary data.

Table 12–65. Scratchpad Register (SPR)

Bit

Name

Function

R/W

Reset

Value

7–0

SPR_WORD

Scratchpad register

R/W

0x00

The two divisor latch registers (DLL and DLH) store the 16-bit divisor for gener-
ation of the baud clock in the baud rate generator. DLL stores the least signifi-
cant part of the divisor. DLH stores the most significant part of the divisor.

DLL and DLH can only be written to before sleep mode is enabled (that is,
before IER[4] is set).

Table 12–66. Divisor Latch Low Register (DLL)

Bit

Name

Function

R/W

Reset

Value

7–0

CLOCK_LSB

Used to store the 8-bit LSB divisor value

R/W

0x00

Table 12–67. Divisor Latch High Register (DLH)

Bit

Name

Function

R/W

Reset

Value

7–0

CLOCK_MSB

Used to store the 8-bit MSB divisor value

R/W

0x00

To achieve the required baud rate, you must program DLL/DLH with the
integer part of the divisor value.

Choosing the appropriate divisor value:

UART: Divisor value = Operating Frequency/(16 x baud rate).

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

Omnia Volt Quick Start Installation Manual preview
Volt
Бренд: Omnia Страницы: 6
IEI Technology WSB-H610 User Manual preview
WSB-H610
Бренд: IEI Technology Страницы: 187
IEI Technology TANK-XM811 User Manual preview
TANK-XM811
Бренд: IEI Technology Страницы: 71
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Бренд: National Instruments Страницы: 162
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Бренд: Teagle Страницы: 40
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Бренд: IEI Technology Страницы: 3
Edge-Core SDW100 Quick Start Manual preview
SDW100
Бренд: Edge-Core Страницы: 7
AMD SB710 User Manual preview
SB710
Бренд: AMD Страницы: 20
Telex Communications 2472AA Instruction Manual preview
2472AA
Бренд: Telex Communications Страницы: 28
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Бренд: Moxa Technologies Страницы: 2
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Бренд: Cytron Technologies Страницы: 13
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Бренд: M86 Security Страницы: 309
Sangoma A200 Analog Installation Manual preview
A200 Analog
Бренд: Sangoma Страницы: 6
PMD DK55110 Manual preview
DK55110
Бренд: PMD Страницы: 74
Paradyne MIM-4000F Installation Instructions Manual preview
MIM-4000F
Бренд: Paradyne Страницы: 6
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Бренд: IEI Technology Страницы: 2
Xantech CC62 Installation Instructions preview
CC62
Бренд: Xantech Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды