— 1 —
— 2 —
— 3 —
PowerTrans Switch
PT-7710 Series
Hardware Installation Guide
First Edition, May 2008
Package Checklist
The Moxa PowerTrans switch is shipped with the following items. If any
of these items are missing or damaged, please contact your customer
service representative for assistance.
y
1 Moxa PowerTrans Switch
y
Hardware Installation Guide
y
CD-ROM with User’s Manual and SNMP MIB file
y
Moxa Product Warranty Statement
y
RJ45 to DB9 console port cable
y
Protective caps for unused ports
y
2 rack-mount ears
Panel Layouts
2
4
6
8
1
3
5
7
PT-7710
LNK/ACT
SPEED
FDX/HDX
FAULT
MASTER
COUPLER
STAT
PWR1
PWR2
RING PORT
COUPLER
PORT
MODE
3
7
4
8
2
6
1
5
2
1
M2
M1
PT-7710
8
7
6
1
3
2
4
5 10
9
Front View (Front Cabling)
Rear View (Front Cabling)
STAT
FAULT
LNK/ACT
SPEED
FDX/HDX
RING PORT
COMUPLER
PORT
PWR1
MASTER
PWR2
COUPLER
M2
M1
MODE
Top View (Down Cabling)
1.
System status LEDs
2.
Interface Module mode LEDs
3.
Interface Module port LEDs
4.
Push-button switch to select mode for Interface Module
5.
Model Name
6.
Fast Ethernet Interface Modules
7.
Gigabit Ethernet Interface Modules
8.
Serial Console port
9.
10-pin terminal block for power inputs, and relay output
10.
Rack Mounting Kit
Dimensions (unit = mm)
31.8
462.5
266.5
Rear View
Top View
Side View
Side View
Front View
219.3
31.8
44
195
209.4
31.8
44
24.3
Fast Ethernet Interface Modules (for slot 1)
96.8
40.7
40.7
96.8
96.8
40.7
40.7
96.8
PM-7200-8TX
PM-7200-1LSC6TX
PM-7200-4MSC2TX/PM-7200-4SSC2TX
PM-7200-4MST2TX
PM-7200-6MST
PM-7200-2MST4TX
PM-7200-6MSC/PM-7200-6SSC
PM-7200-2MSC4TX/PM-7200-2SSC4TX
96.8
40.7
96.8
40.7
40.7
96.8
96.8
40.7
Gigabit/Fast Ethernet Interface Modules (for slot 2)
40.7
86.6
40.7
40.7
40.7
40.7
86.6
86.6
86.6
86.6
PM-7200-1MSC/ PM-7200-1SSC
PM-7200-2MSC/PM-7200-2SSC
PM-7200-2MST
PM-7200-2GTXSFP
PM-7200-1MST
Rack Mounting
Use four screws to attach the PT switch to a
standard rack.
Wiring Requirements
WARNING
Safety
First!
Be sure to disconnect the power cord before installing
and/or wiring your Moxa PowerTrans Switch.
Calculate the maximum possible current in each power
wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire
size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
Grounding the Moxa PowerTrans Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
Wiring the Power Inputs
The PT series of switches supports
dual redundant power supplies (DC
power only): VDC “Power Supply 1
(PWR1)” and “Power Supply 2
(PWR2)”, or VAC “Power Supply
(PWR1)”. The connections for
PWR1, PWR2 and the RELAY are
located on the terminal block. The
front view of the terminal block
connectors are shown below.
Wiring the Relay Contact
Each PT switch has one relay output. Refer to the next section for
detailed instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the terminal
block receptor.
FAULT
: The relay contact of the 10-pin terminal block connector are
used to detect user-configured events. The two wires attached to the
RELAY contacts form an open circuit when a user-configured event is
triggered. If a user-configured event does not occur, the RELAY circuit
will be closed.
P/N: 1802077100010
