— 4 —
— 5 —
— 6 —
Wiring the Redundant Power Inputs
Each PT switch has two sets of power inputs: power input 1 and power
input 2.
STEP 1
: Insert the dual set positive/negative DC wires into PWR1 and
PWR2 terminals (+
→
pins 1, 9, -
→
pins 2, 10). Or insert the L/N AC
wires into the PWR1 terminals (L
→
pin 1, N
→
pin 2).
STEP 2
: To keep the DC or AC wires from pulling loose, use a
screwdriver to tighten the wire-clamp screws on the front of the terminal
block connector.
LED Indicators
The front panel of the PT switch contains several LED indicators. The
function of each LED is described in the table below.
LED
Color
State
Description
System LEDs
On
System has passed self-diagnosis
test on boot-up and is ready to run.
GREEN
Blinking System is undergoing the
self-diagnosis test.
STAT
RED On
System failed self-diagnosis on
boot-up.
On
Power is being supplied to the main
module’s power input PWR1.
PWR1
AMBER
Off
Power is not being supplied to the
main module’s power input PWR1.
On
Power is being supplied to the main
module’s power input PWR2.
PWR2
AMBER
Off
Power is not being supplied to the
main module’s power input PWR2.
On
The corresponding PORT alarm is
enabled and a user-configured event
has been triggered.
FAULT
RED
Off
The corresponding PORT alarm is
enabled and a user-configured event
has not been triggered, or the
corresponding PORT alarm is
disabled.
On
This PT switch is the Master of this
Turbo Ring.
Blinking
This PT switch has become Ring
Master of this Turbo Ring after the
Turbo Ring was broken.
MASTER
GREEN
Off
This PT switch is not the Master of
this Turbo Ring.
COUPLER
GREEN
On
When this PT switch enables the
coupling function to form a back-up
path.
Off
When this PT switch disables the
coupling function.
Mode LEDs
On
The corresponding module port’s
link is active.
Blinking The corresponding module port’s
data is being transmitted.
LNK/ACT
GREEN
Off
The corresponding module port’s
link is inactive.
Off
The corresponding module port’s
data is being transmitted at 10
Mbps.
On
The corresponding module port’s
data is being transmitted at 100
Mbps.
SPEED
GREEN
Blinking
The corresponding module port’s
data is being transmitted at
1000 Mbps.
On
The corresponding module port’s
data is being transmitted in full
duplex mode.
FDX/HDX
GREEN
Off
The corresponding module port’s
data is being transmitted in half
duplex mode.
On
The corresponding module’s port is
the ring port of this PT switch.
RING
PORT
GREEN
Off
The corresponding module’s port is
not the ring port of this PT switch.
On
The corresponding module’s port is
the coupler port of this PT switch.
COUPLER
PORT
GREEN
Off
The corresponding module’s port is
not the coupler port of this PT
switch.
* Slot 2 (M2) is mainly used for Gigabit modules. If 100BaseFX modules
are used in Slot 2 (M2), the modules will not support “Far End Fault”.
The Link/ACT LED indicator will stay at “Green (ON)” status when
Fiber TX cable is unplugged.
Specifications
Technology
Standards
IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x,
802.1D, 802.1W, 802.1Q, 802.1p, 802.1X, 802.3ad
Flow control
IEEE 802.3x flow control, back pressure flow
control
Interface
Fast Ethernet
Slot 1 (M1) for any combination of 6-, 7-, or 8-port
PM-7200 fast Ethernet modules with
10/100BaseT(X) or 100BaseFX (SC/ST connector)
Slot 2 (M2) for a 1- or 2-port interface modules
with 100BaseFX (SC/ST connector)
Gigabit Ethernet
Slot 2 (M2) for 2-port PM-7200 Gigabit Ethernet
combo module with 100/1000BaseT(X) or
1000BaseSFP slots (Slot 2 does not support 10M
FDX/HDX)
Console RS-232
(RJ45)
System LED
Indicators
STAT, PWR1, PWR2, FAULT, MASTER,
COUPLER
Module LED
Indicators
LNK/ACT, FDX/HDX, RING PORT, COUPLER
PORT, SPEED
Alarm Contact
One relay output with current carrying capacity of
3A @ 30 VDC or 3A @ 240 VAC
Optical Fiber (100BaseFX)
Distance Multi-mode
0 to 5 km, 1300 nm (50/125
μ
m, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125
μ
m, 500 MHz*km)
Single-mode
0 to 40 km, 1310 nm (9/125
μ
m, 3.5 PS/(nm*km))
Min. TX Output
Multi-mode: -20 dBm; single-mode: -5 dbm
Max. TX Output
Multi-mode: -10 dBm; single-mode: 0 dbm
RX Sensitivity
Multi-mode: -32 dBm; single-mode: -34 dbm
Power
Input Voltage
24/48 VDC (9 to 60 V), or 110/220 VDC/VAC (88
to 300 VDC and 85 to 264 VAC)
Input Current
Max. 0.81A @ 24 VDC
Max. 0.42A @ 48 VDC
Max. 0.17/0.10 @ 110/220 VDC
Max. 0.20/0.12 @ 110/220 VAC
Physical Characteristics
Housing
IP 30 protection, metal case
Dimensions
(W x H x D)
266.7 x 44 x 195 mm (10.5 x 1.73 x 7.68 in.)
Weight 2200g
Environmental Limits
Operating Temp.
-40 to 85°C (-40 to 185°F)
Cold start of min. 100 VAC at -40
°
C
Storage Temp.
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity.
5 to 95% (non-condensing)
Regulatory Approv
al
s
Safety EN60950-1
(Pending)
Power
Automation
IEC 61850-3, IEEE 1613
Road Traffic
NEMA TS2
Rail Traffic
EN50121-4 (Pending)
Maritime
DNV (Pending), GL (Pending)
EMI
FCC Part 15, CISPR (EN55022) class A
Warranty
5 years
Click here for online support:
www.moxa.com/support
The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)
Europe: +49-89-3 70 03 99-0
Asia-Pacific: +886-2-8919-1230
China: +86-21-5258-9955 (toll-free: 800-820-5036)
©
2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.
