manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

McBSP3

9-21

DSP Public Peripherals

9.4.4.7

Interrupt Flag Configuration and Clear (ILR, ITR, MIR) on Level 2 Handler

1) DSP_Write => ILR; set ILR appropriately for the interrupt handling priority.

2) DSP_Write ITR and (0xFFFF F3FF)=> ITR; clear remaining TX and RX

interrupts.

Note:

This set up is not needed after reset.

3) DSP_Write MIR and (0xFFFF F3FF) => MIR; enabled SPI TX and RX

interrupt

9.4.4.8

Interrupt Flag Configuration MASK Release on Level 2 Handler

DSP_Write MIR and (0xFFFF FFFB) => MIR0; enabled INT4 (level 2 interrupt
FIR)

9.4.4.9

Take Out of Reset for Transmit and Receive Starting (SPCR[1,2])

1) DSP_write SPCR1 or (0x0001) => SPCR1; enabled receive port

2) DSP_write SPCR2 or (0x0001) => SPCR2; enabled transmit port

Note:

Wait two sample rate clock cycles for McBSP stability.

9.4.4.10

Transmit and Received Data Loading (TX_INT Handling in Interrupt Survive Routine)

For data transmit:

1) DSP_Write => DXR; transmit data loading to DXR

2) DSP_Read <= DRR; wait for data read after the RINT

For two data received:

1) DSP_Write => DXR; dummy write 0xFFFF for data receive after the TINT

2) DSP_Read <= DRR; first data read after the RINT

3) DSP_Write => DXR; dummy write 0xFFFF for data receive after the TINT

4) DSP_Read <= DRR; second data read after the RINT

9.4.4.11

Register Setup GPIO Mode

1) DSP_Write SPCR1 and (0xFFFE) => SPCR1; disabled receive port

2) DSP_Write PCR or (0x1000) => PCR; DR pin set as GPI

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Бренд: Javad Страницы: 35
Alcad ZA-431 Quick Start Manual preview
ZA-431
Бренд: Alcad Страницы: 6
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming preview
PARTNER Voice Messaging PC Card Release 2
Бренд: Lucent Technologies Страницы: 67
Avolites Titan One Quick Start Manual preview
Titan One
Бренд: Avolites Страницы: 24
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Бренд: Garland Страницы: 43
Velopex Extra-X Quick Start Manual preview
Extra-X
Бренд: Velopex Страницы: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Бренд: Tandberg Data Страницы: 6
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Бренд: ADC Страницы: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Бренд: Renesas Страницы: 28
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Бренд: Riverbed Страницы: 82
Nortel BayStack 660 Use Manual preview
BayStack 660
Бренд: Nortel Страницы: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Бренд: Baracoda Страницы: 16
Arctic Accelero TWIN TURBO II Installation Manual preview
Accelero TWIN TURBO II
Бренд: Arctic Страницы: 2
Adaptec Serial Attached SCSI (SAS) Expander Card Installation And User Manual preview
Serial Attached SCSI (SAS) Expander Card
Бренд: Adaptec Страницы: 26
netsys NVF-2400S User Manual preview
NVF-2400S
Бренд: netsys Страницы: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Бренд: Spirent Страницы: 22
Matrix Switch Corporation MSC-CP16X4E Product Manual preview
MSC-CP16X4E
Бренд: Matrix Switch Corporation Страницы: 48
ekwb 3831109819395 Manual preview
3831109819395
Бренд: ekwb Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды