manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

Memory Map

 

4-6

4.2

Memory Map

Four external chip-selects and a series of internal address decodes are
provided for external and internal memories and for peripherals attached to the
TI peripheral bus (see Table 4–2). CS0, CS1, CS2, and CS3 each has an
address range of 32M bytes; the external SDRAM space has an address range
of 64M bytes; the internal SRAM space has an address range of 512K bytes.

In the boot overlay mode, CS0 and CS3 are swapped so that the MPU can boot
from a boot flash. Boot overlay mode is entered if pin MPU_BOOT is high dur-
ing reset (the state on the MPU_BOOT signal can change after reset). The
state of this pin is reflected in the BM bit field of the EMIF slow interface
configuration register. For details, see Table 4–12,  EMIF Slow Interface
Configuration Register (EMIFS_CONFIG_REG).

Table 4–2. Device Types Associated With Chip-Select

CS

Device

CS0

External asynchronous RAM
External asynchronous ROM or flash
External synchronous burst flash

CS1

External asynchronous RAM
External asynchronous ROM or flash
External synchronous burst flash

CS2

External asynchronous RAM
External asynchronous ROM or flash
External synchronous burst flash

CS3

External asynchronous RAM
External asynchronous ROM or flash
External synchronous burst flash

None

†

External synchronous dynamic RAM

None

†

Internal SRAM

† The interface to these memory devices is activated via internal address decoding. There is no

external chip select.

The OMAP5910 peripherals are mapped on the MPU memory space in two
different segments: through STROBE0 (public peripherals) and STROBE1
(private peripherals). Each peripheral has a range of 2K bytes.

Table 4–3 shows the MPU memory map.

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
NEC IE-78K0-NS-P04 User Manual preview
IE-78K0-NS-P04
Бренд: NEC Страницы: 72
NEC ELECTRA ELITE IPK II Programming Manual preview
ELECTRA ELITE IPK II
Бренд: NEC Страницы: 617
NEC VERSA DOCK - SERVICE Installation Manual preview
VERSA DOCK - SERVICE
Бренд: NEC Страницы: 8
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Бренд: Tandberg Data Страницы: 2
Edge-Core SDW100 Quick Start Manual preview
SDW100
Бренд: Edge-Core Страницы: 7
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Бренд: N.A.T. Страницы: 32
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Бренд: National Instruments Страницы: 15
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Бренд: ZALMAN Страницы: 18
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Бренд: ATI Technologies Страницы: 20
Technics SH-GE90 Service Manual preview
SH-GE90
Бренд: Technics Страницы: 20
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Бренд: iesy Страницы: 9
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Бренд: Taiwan Commate Computer Inc. Страницы: 25
Greenlee 910FS Instruction Manual preview
910FS
Бренд: Greenlee Страницы: 52
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Бренд: ADLINK Technology Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды