manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

OMAP5910 Configuration Registers

6-67

MPU Private Peripherals

Table 6–49. Module Configuration Control 0 Register (MOD_CONF_CTRL_0) (Continued)

Bit

Reset

Value

R/W

Description

Value

Name

12

CONF_MOD_COM_
MCLK_12_48_SEL_R

This bit determines if the UART2.CLKREQ
output of the OMAP5910 device is 12 MHz
or 48 MHz.

This bit resets to 0, which causes a
12-MHz clock to be seen on MCLK when
UART2.CLKREQ is low. When written to a
1, this bit causes 48-MHz clock to be seen
on MCLK when UART2.CLKREQ is low.
When 1, UART2.CLKREQ also starts the
12-MHz to 48-MHz DPLL.

R/W

0x0

11

CONF_MOD_USB_HOST_
UART_SELECT_R

This bit enables the multiplexing of
UART1.CTS, UART1.RX, and UART1.TX
signals to the USB_HMC host mux module.

R/W

0x0

0

UART1 uses the standard source location
as defined by the OMAP5910 functional
multiplexing.

1

UART1.TX, UART1.RX, and UART1.CTS1
are sourced from the USB_HMC module.

For details on this multiplexing please see
the USB_HMC spec.

10

RESERVED

Reserved for future expansion. This bit
must always be written as 0.

R/W

0x0

9

CONF_MOD_USB_HOST_
HHC_UHOST_EN_R

Enable input for functional-mode clocking
of USB_HHC

R/W

0x0

0

Internal functional mode 48-MHz and
12-MHz clocks are disabled; USB_HHC
can not function as a USB host.

1

Internal functional mode 48-MHz and
12-MHz clocks are enabled.

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

EAW MX8000 Technical Specifications preview
MX8000
Бренд: EAW Страницы: 2
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Бренд: 3Com Страницы: 8
Patton electronics 1084 Installation And Operation Manual preview
1084
Бренд: Patton electronics Страницы: 16
ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Бренд: ebm-papst Страницы: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Бренд: ebm-papst Страницы: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Бренд: ebm-papst Страницы: 5
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Бренд: Paradyne Страницы: 1
BSS Audio EC-4B Installation Manual preview
EC-4B
Бренд: BSS Audio Страницы: 20
Reeven NAIA Installation Manual preview
NAIA
Бренд: Reeven Страницы: 2
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Бренд: Acces I/O products Страницы: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Бренд: Enertronica Santerno Страницы: 34
Keithley PDISO-8 User Manual preview
PDISO-8
Бренд: Keithley Страницы: 71
JETWAY LI1B Series User Manual preview
LI1B Series
Бренд: JETWAY Страницы: 55
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Бренд: Longshine Страницы: 27
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Бренд: Valcom Страницы: 4
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Бренд: TDK Страницы: 13
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Бренд: NXP Semiconductors Страницы: 54
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Бренд: IFM Electronic Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды