manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

DSP Interrupt Interface

8-29

DSP Private Peripherals

Table 8–31. Edge-Triggered/Level-Sensitive Control Register Low

Bit

Name

Value

Description

Type

Reset

Value

15–0

CHx Trig/Level

This bit defines whether channel CHx is edge- or level-
sensitive where CHx corresponds to interrupt channels
nXIRQ[15:0]. Channels nXIRQ[15:0] correspond to the
DSP level 1 interrupts IRQ17:2, respectively.

R/W

0

0

CHx is level-sensitive.

1

CHx is edge-sensitive.

Table 8–32. Edge-Triggered/Level-Sensitive Control Register High

Bit

Name

Value

Description

Type

Reset

Value

15–8

Reserved

0

7

Host Interrupt
Trig/Level

This bit defines whether the host interrupt is edge or
level-sensitive.

R/W

0

NHOSTINT is level-sensitive.

1

NHOSTINT is edge-sensitive.

6

NMI Trig/Level

This bit defines whether the nonmaskable interrupt is
edge or level-sensitive. The NMI channel corresponds to
the DSP NMI interrupt.

R/W

0

0

NMI is level-sensitive.

1

NMI is edge-sensitive.

5–0

CHx Trig/Level

This bit defines whether channel CHx is edge or
level-sensitive, where CHx corresponds to interrupt
channels nXIRQ[21:16]. Channels nXIRQ[21:16]
correspond to the DSP level 1 interrupts IRQ23:18,
respectively.

R/W

0

0

CHx is level-sensitive.

1

CHx is edge-sensitive.

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

CAME Z Series Manual preview
Z Series
Бренд: CAME Страницы: 4
Velopex Extra-X Quick Start Manual preview
Extra-X
Бренд: Velopex Страницы: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Бренд: Tandberg Data Страницы: 6
FONESTAR XO-324 Instruction Manual preview
XO-324
Бренд: FONESTAR Страницы: 8
SeaLevel 7205e User Manual preview
7205e
Бренд: SeaLevel Страницы: 34
Aurora EGO AE120 User Manual preview
EGO AE120
Бренд: Aurora Страницы: 6
Unex EVK-351 Quick Start Manual preview
EVK-351
Бренд: Unex Страницы: 27
Dataprobe iBoot Instruction Manual preview
iBoot
Бренд: Dataprobe Страницы: 16
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Бренд: Hanwha Techwin Страницы: 125
SilverStone SDP12 Quick Start Manual preview
SDP12
Бренд: SilverStone Страницы: 2
HighPoint SSD7202 Quick Installation Manual preview
SSD7202
Бренд: HighPoint Страницы: 12
WIN Enterprises PL-83300 User Manual preview
PL-83300
Бренд: WIN Enterprises Страницы: 25
Rimage CDPR3 User Manual preview
CDPR3
Бренд: Rimage Страницы: 30
Renesas PCA7755D User Manual preview
PCA7755D
Бренд: Renesas Страницы: 6
NI PXIe-1075 User Manual preview
PXIe-1075
Бренд: NI Страницы: 8
Alphacool HDX Pro Air Manual preview
HDX Pro Air
Бренд: Alphacool Страницы: 3
A&D AD-4411 Instruction Manual preview
AD-4411
Бренд: A&D Страницы: 50
SunFounder R3 Manual preview
R3
Бренд: SunFounder Страницы: 527

Бренды по названию

Популярные бренды

Загрузить еще бренды