manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

LCD Controller Registers

11-25

LCD Controller

Table 11–11. LCD Control Register (LCDControl) (Continued)

Bit

Reset

Value

Description

Value

Name

9

M8B

Mono 8-bit mode. Selects 4 or 8 data lines to output pixel data to
the screen.

0

0

LCD_PIXEL[3:0] is used to output four pixel values to the panel
each pixel clock transition.

1

LCD_PIXEL[7:0] is used to output eight pixel values to the panel
each pixel clock transition.

This bit is ignored in al other modes.

8

LCDCB0

LCD control bit 0. Used with LCD control bit 1 to control mapping
of pixel data from the frame buffer to the output bus LCD.P[16:0].

See Table 11–16 for proper settings for this field.

0

7

LCDTFT

LCD TFT

0

0

Passive or STN display operation enabled, dither logic is enabled

1

Active or TFT display operation enabled, external palette and DAC
required, dither logic bypassed, pin timing changes to support
continuous pixel clock, output enable, VSYNC, HSYNC signals

5–6

–

Reserved

0

4

LoadMask

Load mask

0

0

Mask out the loaded palette interrupt

1

Mask not active

3

Done-
Mask

Done mask

0

0

Mask out the frame done (done) interrupt

1

Mask not active

2

-

Reserved

0

1

LCDBW

LCD Monochrome

0

0

Color operation enable

1

Monochrome operation enabled

0

LCDEN

LCD controller enable

0

0

LCD controller disabled

1

LCD controller enabled

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Бренд: SAF Страницы: 30
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Бренд: B&B Electronics Страницы: 4
OpenVox B800P User Manual preview
B800P
Бренд: OpenVox Страницы: 13
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Бренд: Concept Pro Страницы: 28
Hama 00176547 Operating Instruction preview
00176547
Бренд: Hama Страницы: 25
Extreme Networks ExtremeCloud Appliance E1120 User Manual preview
ExtremeCloud Appliance E1120
Бренд: Extreme Networks Страницы: 219
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Бренд: FOLSOM Страницы: 89
ICP DAS USA ET-7017-10 Quick Start Manual preview
ET-7017-10
Бренд: ICP DAS USA Страницы: 8
Alphacool HDX Pro Air Manual preview
HDX Pro Air
Бренд: Alphacool Страницы: 3
Renesas RL78 Series User Manual preview
RL78 Series
Бренд: Renesas Страницы: 31
Terasic DE10-Agiles User Manual preview
DE10-Agiles
Бренд: Terasic Страницы: 208
WATT & WELL SECC Series Getting Started preview
SECC Series
Бренд: WATT & WELL Страницы: 15
ADF Web AXIS HD67555 User Manual preview
AXIS HD67555
Бренд: ADF Web Страницы: 20
Dell 2000FP Installation Instructions Manual preview
2000FP
Бренд: Dell Страницы: 10
NEC NEAX 2400 Integration Manual preview
NEAX 2400
Бренд: NEC Страницы: 168
Telstra NTU-45E Quick Reference Manual preview
NTU-45E
Бренд: Telstra Страницы: 2
Philips 22AV1132 Brochure preview
22AV1132
Бренд: Philips Страницы: 2
Philips 22AV1132 Specifications preview
22AV1132
Бренд: Philips Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды