manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

MPU TI Peripheral Bus Bridges

2-65

MPU Subsystem

2.10 MPU TI Peripheral Bus Bridges

The MPU TI peripheral bus (TIPB) bridges (see Figure 2–23) connect the
TI925T to its peripherals. Two MPU TIPBs, one private and one nonprivate or
public, are implemented to reduce access latency and improve system perfor-
mance. Concurrent transfers are possible if there are no resource conflicts; for
example, DMA transfers to the public TIPB and the TI925T both access the
private TIPB simultaneously. The timers are connected on the private periph-
eral bus for low-latency access by an operating system, and the camera is
located on the public peripheral bus for access by the DMA.

The private and public peripheral bridges are compatible with the TIPB
specification.

Figure 2–23. MPU TI Peripheral Bus Bridge Connections

System

DMA

controller

MPU

TI

bridge

(private)

bridge

(shared)

Logic

Mux

Logic

TI peripheral bus)

Private TI peripheral bus)

Public TI peripheral bus

32

32

peripheral

bus

TI

peripheral

bus

TI peripheral bus

Mux

2.10.1 8-Bit, 16-Bit, and 32-Bit Word Access

The MPU TIPB handles 8-bit, 16-bit, and 32-bit word accesses. Data is loaded
and stored in little endian fashion. Data is always right-justified on the TIPB.

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

Barco EX Safety Manual preview
EX
Бренд: Barco Страницы: 100
dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
Quatech DS-3000 User Manual preview
DS-3000
Бренд: Quatech Страницы: 27
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Бренд: M86 Security Страницы: 46
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Бренд: National Instruments Страницы: 36
Lancom 7100 VPN Manual preview
7100 VPN
Бренд: Lancom Страницы: 70
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Бренд: Longshine Страницы: 27
Renesas E200F User Manual preview
E200F
Бренд: Renesas Страницы: 76
hilscher netHOST NHST-T100 User Manua preview
netHOST NHST-T100
Бренд: hilscher Страницы: 75
CompuLab CL-SOM-AM57 Series Reference Manual preview
CL-SOM-AM57 Series
Бренд: CompuLab Страницы: 79
Renesas M34502T-MCU User Manual preview
M34502T-MCU
Бренд: Renesas Страницы: 40
Aviosys 9255W User Manual preview
9255W
Бренд: Aviosys Страницы: 77
ENERMAX ELC-LMT120-RGB User Manual preview
ELC-LMT120-RGB
Бренд: ENERMAX Страницы: 33
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Бренд: Renesas Страницы: 18
Dantel 44118 Installation & Operation Manual preview
44118
Бренд: Dantel Страницы: 22
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Бренд: Moxa Technologies Страницы: 2
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Бренд: Broadband Products Страницы: 16
QSC Q-SYS QIO-GP8x8 Hardware User Manual preview
Q-SYS QIO-GP8x8
Бренд: QSC Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды