manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

MPU Memory Management Unit

 

2-46

-

Section: If the level 1 descriptor defines a section-mapped access, its AP
bits define whether or not the the access is allowed (see Table 2–24).
Their interpretation is dependent upon the setting of the S bit (CP15 con-
trol register bit 8). If the access is not allowed, a section permission fault
is generated.

-

Subpage: If the level 1 descriptor defines a page-mapped access, the
level 2 descriptor specifies four access permission fields (ap3..ap0), each
corresponding to one quarter of the page. ap0 corresponds to the subpage
located at the lowest addresses. The selected AP bits are then interpreted
in the same way as for a section and may generate a subpage permission
fault.

2.7.12 External Aborts

In addition to the MMU-generated aborts, the TI925T has an external s_abort
port, which can be used to flag errors on external memory accesses. However,
not all accesses can be aborted this way, so this signal must be used with great
care. This section describes the restrictions.

The accesses listed below can be aborted and restarted safely. In the case of
an interlocked read-write (SWAP instruction) in which the read aborts, the
write does not happen.

-

Reads

-

Unbuffered writes

-

Level-1 descriptor fetch

-

Level-2 descriptor fetch

-

Interlocked read-write (SWAP)

-

Cacheable reads (line fetches)

A cache line fetch can be safely aborted on any word in the transfer. If an abort
occurs during the line fetch, the cache line is invalidated. In addition, if the abort
happens upon or before the instruction the TI925T requested, the instruction
is aborted. If the abort happens after, the cache line is simply marked as
invalid.

2.7.13 Buffered Writes

Buffered writes cannot be aborted externally. Therefore, the system must be
configured in such a way that it does not perform buffered writes to areas of
memory that can generate an external abort.

There are three instances of MMU: the DSP MMU, the MPU instruction cache
MMU, and the MPU data cache MMU

.

 The MPU MMU is that of the TI925T.

Because there are multiple MMUs, it is the responsibility of the OS (system
software) to ensure data coherence.

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Бренд: IBA Страницы: 29
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Unex EVK-351 Quick Start Manual preview
EVK-351
Бренд: Unex Страницы: 27
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Бренд: Ista Страницы: 16
Goobay 97790 User Manual preview
97790
Бренд: Goobay Страницы: 28
Kontron KISS Stor Slim Quick Installation Manual preview
KISS Stor Slim
Бренд: Kontron Страницы: 4
X-Micro XWL-11GPAR User Manual preview
XWL-11GPAR
Бренд: X-Micro Страницы: 24
VALKYRIE Dragonfang 240 Installation Manual preview
Dragonfang 240
Бренд: VALKYRIE Страницы: 26
Epson IMU G Series User Manual preview
IMU G Series
Бренд: Epson Страницы: 19
Epson PP-100 III Setup Manual preview
PP-100 III
Бренд: Epson Страницы: 2
Epson OT-WL02 Technical Reference Manual preview
OT-WL02
Бренд: Epson Страницы: 23
Epson MF1436-02 User Manual preview
MF1436-02
Бренд: Epson Страницы: 35
Epson M-G3 Series User Manual preview
M-G3 Series
Бренд: Epson Страницы: 21
Epson E0C6011 Development Manual preview
E0C6011
Бренд: Epson Страницы: 49
Epson E0C6006 Technical Manual preview
E0C6006
Бренд: Epson Страницы: 63
Epson S1C6200 Core Cpu Manual preview
S1C6200
Бренд: Epson Страницы: 98
Epson S1C63454 Technical Manual preview
S1C63454
Бренд: Epson Страницы: 131
Epson E0C6001 Technical Manual preview
E0C6001
Бренд: Epson Страницы: 146

Бренды по названию

Популярные бренды

Загрузить еще бренды