Panasonic MINAS A6 Series Скачать руководство пользователя страница 356 | Manualshive

Страница: 356 / 560

background image

5-64

5

5. Manual Gain Tuning (Application)

Adjustment

Two-degree-of-freedom control mode (Velocity control mode)

Outline

In the two-degree-of-freedom control mode, command response and servo rigidity can be
independently set with improved responsiveness. This mode has enhanced speed con-
trol functions.

Applicable Range

This function can be applicable only when the following condition are satisfied.

Conditions under which

the Two-degree-of-freedom control mode is activated.

Control Mode

Speed control

Others

• Should be servo-on condition.
• Factors other than control parameters such as torque limit should be

properly setup, allowing motor to operate normally.

Related Parameter

First, set Pr6.47 Function expansion setup 2 to 1 and write the setting to EEPROM. Re

-

set the control power supply to enable the two-degree-of-freedom control mode. Adjust
the gain by using the real-time auto-tuning (refer to P.5-10). If further improvement is nec-

essary, manually fine tune the following parameters while checking the response.

Class No.

Title

Function

6

47

Function

expansion

settings 2

Set up various functions bit by bit.
bit 0 Two-degree-of-freedom control mode

0: Invalid

1: Valid

*

The least significant bit is represented by bit0.

2

22

First order filter

time constant

for command

While the two-degree-of-freedom control real-time auto-

tuning is selected, time constant of command filter is applied
with the maximum value limited to 640 (= 64.0 ms).

(The value of the parameter is not limited but the value to be
applied to driver is limited.)
Decreasing the value of this parameter makes command
response fast and large, resulting smooth command
response.

6

48

Adjust filter

To set the time constant of adjustment filter.
When the torque filter setting is changed, set the adjustment
filter to a near value while referring to setting of real-time
auto-tuning. In addition, by finely adjusting the adjustment
filter while monitoring the encoder position deviation in the

vicinity of steady state, overshoot or vibration waveforms
may be sometimes improved.

Related page

• P.4-6 to P.4-85... “Details of parameter”

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

«
...
354
355
356
357
358
...
»

Содержание MINAS A6 Series

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MINAS A6 Series

Бренд: ABATEC Страницы: 8

Бренд: M&C Страницы: 16

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Origami 4M-006-01

Бренд: 4 Moms Страницы: 28

Бренд: Canarm Страницы: 3

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Elby Designs Страницы: 4

KOOL STRIDE KS-S

Бренд: KOOL-STOP Страницы: 8

Бренд: WAGO Страницы: 16

Бренд: TEL Страницы: 26

Бренд: Vimar Страницы: 32

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Freedom Bridge FB3

Бренд: Identiv Страницы: 2

Бренд: Cypress Страницы: 571

Бренд: Conductrix Wampfler Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды