Panasonic MINAS A6 Series Скачать руководство пользователя страница 403 | Manualshive

Страница: 403 / 560

background image

6-31

1

Before Using the Products

2

Preparation

3

Connection

4

Setup

5

Adjustment

6

When in T

rouble

7

Supplement

2. Setup of gain pre-adjustment protection

4-2) In case two degree-of-freedom control is invalid (Pr6.47 bit 0 = 0)

• For Pr5.20 = 0 (detection through command position deviation),

Pr0.14 “Position deviation excess setting” = Vc/Kp × (1.2 to 2.0)
Vc: Maximum frequency of positional command pulse [pulse (command unit)/s]
Kp: Position loop gain [1/s]
Factor in ( ) is margin to prevent frequent activation of position deviation excess protection.

Note 3) When switching position loop gain Kp, select the smallest value for calculation.
Note 4) When using the positional command filter and damping control, add the following values.

Positional command smoothing filter: Vc × Filter time constant [s]
Positional command FIR filter: Vc × Filter time constant [s]/2
Damping control: Vc/(π × Damping frequency [Hz])

.

• For Pr5.20 = 1 (Detection through encoder position deviation and full-closed position deviation)

Pr0.14 “Position deviation excess setting” = Ve/Kp × (1.2 to 2.0)
Ve: Maximum operation frequency [pulse/s] in encoder unit or full-closed unit
Kp: Position loop gain [1/s]

Note 5) NOTE 3) When switching position loop gain Kp, select the smallest value for calculation.

Note 6) When Pr5.20 = 1, setups of positional command filter and damping control have no effect.

P.4-14 (Pr0.14)

，

P.4-58 (Pr5.20)

5) Motor working range setup

During the position control or full-closed control, this function detects the motor posi-
tion which exceeds the revolutions set to Pr5.14 Allowable motor operating range set-

ting, and issues Err34.0 Motor working range limit protection.

For details, see 6-3 Motor working range setup functions.

P.4-56 (Pr5.14)

6) Hybrid deviation excess error protection setup

At the initial operation with full-closed control, operation failure may occur due to re-
verse connection of external scale or wrong external scale division ratio.

To indicate this type of defect, Err25.0 “Hybrid deviation excess error protection” is is

-

sued when the deviation of motor position (encoder unit) and load position (external

scale unit) exceed Pr3.28 “Hybrid deviation excess setting.”

For details, see 4-5-3 Setting of hybrid deviation excess.

P.4-38 (Pr3.28)

Related page

Related page

Related page

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

«
...
401
402
403
404
405
...
»

Содержание MINAS A6 Series

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MINAS A6 Series

Бренд: ABB Страницы: 2

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: C&K systems Страницы: 2

Бренд: CAME Страницы: 32

Бренд: Babybee Prams Страницы: 21

Бренд: 1Control Страницы: 8

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Eaton Страницы: 6

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: tams elektronik Страницы: 12

Бренд: IBM Страницы: 38

Бренд: PACH & COMPANY Страницы: 4

Бренд: Ziton Страницы: 36

Бренд: MX Страницы: 12

Бренд: CORNING Страницы: 12

Бренд: Samson Страницы: 44

Бренд: Hansen Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды